28.09.2010, 19:43 | #1 |
Пользователь
Регистрация: 28.09.2010
Адрес: Кострома
Сообщений: 39
Репутация: 0
|
Help 2060
Что за зверь-ошибка 10-367? Как сделать так чтобы ее не было и было хорошо? Всем спасибо Сергей P.S. может кто даст ссылку на коды ошибок или сервисную информацию, чтобы по пустякам не дергать. __________________ Назаренко Сергей, Костромской печатный дом 8 903 6341330, 8 0942 31-02-08, 31-19-39 kvartan@yandex.ru |
28.09.2010, 22:04 | #2 |
Местный
Регистрация: 26.04.2009
Адрес: Новосибирск
Сообщений: 1,568
Репутация: 235
|
10-367 Heat Roll Overheat Fail 2
The Heat Roll Overheat Thermistor detected a temperature in excess of 200 °C (392°F) on the Heat Roll while running heavy weight paper. NOTE: This status code is stored in NVM location 744-016 and cannot be reset by Power Off/ Power On. To reset the code, enter Diagnostics and change the value in NVM location 744-016 Heat Roll Over Heat Fail 2 from “1” to “0”. Initial Actions Refer to BSD 10.1 for the following procedure. Perform the following: • Ensure that the Fuser Upper Fan is clean, there are no obstructions in the air flow path and is operational. If not operational, go to 1-358 Fuser Upper Fan Failure RAP. • Ensure that the Fuser Lower Fan is clean, there are no obstructions in the air flow path and is operational. If not operations, go to 1-359 Fuser Lower Fan Failure RAP. • Perform the GP 11 Fuser Belt Cooling Fan Check-out Procedure to determine if the Fuser Belt Cooling Fan/s are operating. • Check the Heat Roll Overheat Thermistor for signs of debris, damage or excessive wear at the point where the Thermistor contacts the Heat Roll (PL 8.2). If the surface of the Thermistor is worn, replace the Heat Roll Overheat Thermistor (REP 10.15). • Inspect the surface of the Heat Roll for excessive wear due to the Thermistor. Replace the Heat Roll if necessary (REP 10.10). Для начала проверьте датчик нагрева вала. Обычно он повреждается, когда бумага намотанная на валы, нещадно выдергивается. Также не забудьте сбросить на ноль вышеуказанный NVM. |
23.10.2010, 21:54 | #3 |
Новичок
Регистрация: 23.10.2010
Адрес: москва
Сообщений: 3
Репутация: 0
|
Эх,давно это было...
У вас перегрелся вал.Заходим в MaxSetup,ищим в NVM номерок 744-016 там стоит "1" ван нужно поставить "0". Тоже самое бывает и с IBT когда поставят не ровно.он сползает и выдает ошибку. |
15.11.2010, 10:05 | #4 |
Местный
Регистрация: 15.08.2008
Адрес: wqe
Сообщений: 434
Репутация: 34
|
|
|
"Форум индустрии цифровой печати" 2008-2023 Все вопросы по сотрудничеству: Электропочта: info@trade-print.ru Москва, Печатников пер. |