|
|
Регистрация | Пригласить друга | Все альбомы | Файловый архив | Справка | Сообщество | Календарь | Сообщения за день | Поиск |
|
Опции темы |
23.09.2009, 19:33 | #1 |
Местный
|
Как отключить счетчик юнита через меню КМ 252Р
PS на второй картинке окошко, которое появляется при запуске проги, там видимо следует выбирать номер com порта. на первой - как я понял сама прога, но на ней никакие кнопочки не работают, хоть куда тыкай, результат никакой. |
28.01.2011, 20:57 | #41 |
Местный
Регистрация: 08.03.2009
Адрес: Москва
Сообщений: 944
Репутация: 90
|
через меню. Это Сервис Мод
|
23.02.2011, 19:38 | #42 |
Новичок
Регистрация: 01.01.2011
Адрес: ladyzhin, Vinnitza region
Сообщений: 13
Репутация: 0
|
Подскажите пожалуйста где скачать SimWin? нашел ссылку только на PirateBay.com и то не качает...
|
24.02.2011, 07:48 | #43 |
Местный
|
|
02.03.2011, 16:08 | #44 |
Новичок
Регистрация: 02.03.2011
Адрес: г. Благодарный
Сообщений: 2
Репутация: 0
|
hirurg_neo спасибо сделал как описано все получилось огромный респект
|
14.03.2011, 23:12 | #45 |
Местный
Регистрация: 11.03.2011
Адрес: Russia
Сообщений: 777
Репутация: 44
|
|
15.03.2011, 20:40 | #46 |
Местный
Регистрация: 03.02.2010
Адрес: Тирасполь
Сообщений: 1,233
Репутация: 45
|
hatrix, 353p SimWin подключается по сети.
|
15.03.2011, 23:46 | #47 |
Местный
Регистрация: 11.03.2011
Адрес: Russia
Сообщений: 777
Репутация: 44
|
Принтер сетевой, попробовал с разных компов, так же подключал через юсб и через ком-порт... Не работает... Постоянно вот так
а потом вместо диалога черная пустота |
16.03.2011, 00:12 | #48 |
Местный
Регистрация: 03.02.2010
Адрес: Тирасполь
Сообщений: 1,233
Репутация: 45
|
hatrix, Там после черного окошка есть пояснение!
REStart-Up Procedure 1)Install the printer body to the external application mode 2)Turn the switch of the printer body off. 3)Confirm the IP address of the connecting PC 4)Connect the printer body and PC with LAN cable. 5)Press the OK key and then turn the switch of the printer body on. кабелем на COM порт не получится - ТОЛЬКО по сети |
17.03.2011, 18:55 | #49 | |
Местный
Регистрация: 22.09.2008
Адрес: РФ
Сообщений: 589
Репутация: 81
|
Цитата:
Напрямую втыкал к компу с симвином через компорт без всякой сети. Делал все по инструкции откуда скачивал (инструкция на англ.яз) |
|
21.03.2011, 12:11 | #50 |
Местный
Регистрация: 11.03.2011
Адрес: Russia
Сообщений: 777
Репутация: 44
|
Это я для 353-го спрашивал, там по сети, да. Уже разобрался, сервисный мануал помог.
|
|
04.08.2011, 18:10 | #51 |
Новичок
Регистрация: 04.08.2011
Адрес: Белебей
Сообщений: 4
Репутация: 0
|
ребят, один вопрос. "please replace IU" это как-либо с барабанами связано? или именно эти чипы?
не очень-то я пока разобрался в этом всем. |
04.08.2011, 18:22 | #52 |
Местный
Регистрация: 15.03.2011
Адрес: Украина
Сообщений: 411
Репутация: 3
|
|
04.08.2011, 18:34 | #53 |
Новичок
Регистрация: 04.08.2011
Адрес: Белебей
Сообщений: 4
Репутация: 0
|
|
04.08.2011, 18:59 | #54 |
Местный
Регистрация: 02.12.2010
Адрес: гнездо
Сообщений: 158
Репутация: 6
|
|
04.08.2011, 19:23 | #55 |
Новичок
Регистрация: 04.08.2011
Адрес: Белебей
Сообщений: 4
Репутация: 0
|
это я и пытался выяснить) спасибо)
черт, они ж дорогие.. |
04.08.2011, 19:25 | #56 |
Местный
Регистрация: 02.12.2010
Адрес: гнездо
Сообщений: 158
Репутация: 6
|
|
04.08.2011, 20:09 | #57 | |
Новичок
Регистрация: 04.08.2011
Адрес: Белебей
Сообщений: 4
Репутация: 0
|
Цитата:
мастер говорил это из-за ленты переноса. вот сказать честно пробег какой не знаю. работаю там недавно, но вроде приличный. с чипами сегодня сделал пару попыток - не увенчались удачей. |
|
06.09.2011, 22:07 | #58 | |
Новичок
Регистрация: 06.09.2011
Адрес: махачкала
Сообщений: 5
Репутация: 0
|
Цитата:
в версии SimWin_C353P_D00-55 создался файл dummymio.ini но с 0.0.0.0 адресом. изменил на IP принтера... так же... возможно принтер нужно перевести в этот самый режим, но не нашел где... думал справлюсь сам, но без вашей помощи ни как. |
|
13.10.2011, 13:45 | #59 |
Местный
Регистрация: 11.03.2011
Адрес: Russia
Сообщений: 777
Репутация: 44
|
1. Connect the PC to the printer with a network cable.
NOTE • The network cable must be a straight-through cable. 16.1.2 Starting the PC and the printer NOTE: • The notebook PC should be started up, and the printer should be turned on before the External Panel Controller is started up. • If an error message appears, follow the instructions described in the message. • Do not quit the External Panel Controller while it is being used. If it is quit, restart the machine and the External Panel Controller. 1. Turn on the machine. 2. Press the Menu/Select key. 3. Press the ▼ key to select “Service Mode.” 4. Press the Menu/Select key. 5. Input the password, and press the Menu/Select key. 6. Check that “System Settings” is selected and press the Menu/Select key. 7. Press the ▼ key to select “SoftwareSWSetting.” 8. Press the Menu/Select key. 9. Select Software-SW “62” and press the Menu/Select key. 10. Press the ▼ key to select “Set by Hex.” 11. Change the setting from “00” to “01” and press the Menu/Select key. 12. Press the Cancel key. 13. Turn off the machine. 14. While the printer remains OFF, turn ON the PC. 15. Check that the computer’s IP address and subnet mask are set as follow: IP address: 192.168.1.100 Subnet mask: 255.255.255.0 16. Turn ON the power switch of the printer and start External Panel Controller on the PC. NOTE: • It may take some time to start External Panel Controller. 17. Check that the External Panel Controller appears in the computer screen. NOTE: • If the External Panel Controller does not appear in the computer screen, turn the printer off, then on again, and then restart the External Panel Controller. |
13.10.2011, 14:05 | #60 |
Местный
Регистрация: 11.03.2011
Адрес: Russia
Сообщений: 777
Репутация: 44
|
16.1.3 Jig software disconnection procedures
• After the jig software (external panel controller) has been used, the external application mode must be canceled (by setting HEX Assignment of software SW “62” to “00”). • The following two procedures are available. A. Disconnection procedure performed from the PC 1. Select [Service Mode] → [System 2] → [Software Switch Setting]. 2. Click [Switch No.] and enter “62” with the ten-key pad. 3. Click [HEX Assignment] and enter “00” with the ten-key pad. 4. Click [Fix]. 5. Disconnect the network cable and turn OFF and then turn ON the printer. B. Disconnection procedure performed from the printer 1. Turn OFF the power switch of the printer. 2. Turn ON the power switch with the Menu/Select key held down. 3. Trouble reset screen will appear. 4. Select [Release Ext. APP], and press the Menu/Select key. 5. Following the instructions given on the screen, turn OFF and then turn ON the printer. 6. This automatically sets HEX Assignment of software SW “62” to “00” and the printer is started. 7. Disconnect the network cable. |
|
"Форум индустрии цифровой печати" 2008-2023 Все вопросы по сотрудничеству: Электропочта: info@trade-print.ru Москва, Печатников пер. |