|
|
Регистрация | Пригласить друга | Все альбомы | Файловый архив | Справка | Пользователи | Календарь | Поиск | Сообщения за день | Все разделы прочитаны |
|
Опции темы |
09.03.2009, 11:26 | #1 |
Местный
|
Ошибка xerox dc 12 3-317 срочно
появилась после того как поставил в ячейке 752-008 значение 3 т.е. использовать ток как принтер. Помогите пожалста! |
09.03.2009, 11:39 | #2 |
Местный
|
я в ужасе горит ошибка 3-317 но дисишка вполне адекватно все печатает!
Как ее сбросить? в нвм зайти нельзя.... что делать? |
09.03.2009, 11:48 | #3 |
Администратор
Регистрация: 19.06.2008
Адрес: Александров
Сообщений: 6,215
|
Эт что то новенькое...
|
09.03.2009, 13:25 | #4 |
Местный
|
ну вот честно такая беда....
а на забугорном сайте я нашел ответ: тип можно обнулить ее ток с компа через сервисную прогу! |
12.03.2009, 15:36 | #5 |
Местный
Регистрация: 13.12.2008
Адрес: Украина
Сообщений: 529
Репутация: 53
|
|
12.03.2009, 16:50 | #6 |
Местный
|
я знаю, ну а из пвски это можно сделать?
|
16.06.2009, 18:10 | #7 |
Гость
Сообщений: n/a
|
3-317 UI/IOT Communications Fail RAP
Description This Fault Code indicates that a communications failure between the UI PWB and the IOT PWB was detected. Initial Action Refer to BSD 3.1 PWB Communications (UI) and BSD 3.12 Monitoring, in this procedure: Procedure PO/PO the machine. If Fault Code 3-317 is still declared, perform the following: Go to Flag 3 on BSD 3.1. +24 VDC is measured at J490-7, and +5 VDC is measured at J490-2 on the UI PWB ( PL 9.5). Yes No Unanswered Perform the following: Go to the +24 VDC-1 Wirenet and check for an open/short circuit Go to the +24 VDC Power (IIT/IPS LVPS) RAP Go to the +5 VDC-1 Wirenet and check for an open/short circuit Go to the +5 VDC Power (IIT/IPS) RAP Perform the following: Go to Flag 1 on Flag 2 on BSD 3.1 and check the following wires for an open/short circuit: Check the wire between IOT CPU PWB P/J404-B14 and UI PWB P/J490-10 Check the wire between IOT CPU PWB P/J404-B13 and UI PWB P/J490-11 Check the wire between IOT CPU PWB P/J404-B16 and UI PWB P/J490-12 Check the wire between IOT CPU PWB P/J404-B15 and UI PWB P/J490-13 Replace the UI PWB ( PL 9.5) Replace the IOT CPU PWB ( PL 9.2) |
16.06.2009, 18:18 | #8 |
Местный
Регистрация: 07.09.2008
Адрес: Донецк
Сообщений: 4,538
Репутация: 461
|
DesignMan, посмотри на дату сообщения... .
|
Опции темы | |
|
"Форум индустрии цифровой печати" 2008-2023 Все вопросы по сотрудничеству: Электропочта: info@trade-print.ru Москва, Печатников пер. |