Ошибки DCP 7**

[dastin]

часть первая

002-500 RAP Error in CUI scan panel UI detection.
002-770 RAP Insufficient HDD capacity while processing the job template within a job.
003-310 RAP IISS extended memory capacity shortage in spite of "With FaxCard" (below 256MB). After avoiding detection condition of 116-389 at power on, extended memory capacity in document scanning area below 256MB is detected with IITsc-detected FaultCode, while FaxCard is mounted. Limitations at the error occurrence are as follows:
003-318 RAP IIIT software failure.
003-319 RAP IIT Video Driver Detection Fail. An internal processing error occurred in the ESS PWB.
003-320 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 1.)
003-321 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 2.)
003-322 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 3.)
003-323 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 4.)
003-324 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 5.)
003-325 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 6.)
003-326 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 7.)
003-327 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 8.)
003-328 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 9.)
003-329 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 10.)
003-330 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 11.)
003-331 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 12.)
003-332 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 13.)
003-333 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 14.)
003-334 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 15.)
003-335 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 16.)
003-336 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 17.)
003-337 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 18.)
003-338 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 19.)
003-339 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 20.)
003-340 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 21.)
003-341 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 22.)
003-342 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 23.)
003-343 RAP ESS PWB detected a communication failure between IIT and ESS. (IIT-ESS Communication Fail 24.)
003-344 RAP This status code is displayed for a power on hotline failure.
003-345 RAP X PIO Unmatch Fail 1. An abnormality with the X hot line was detected when an X job failure was received from the IIT.
003-346 RAP X PIO Mismatch Fail 2. An abnormality with the X hot line was detected when IIT image delivered was received from the IIT.
003-356 RAP All scanned original sheets judged as Blank by Blank Paper Detection.
003-701 RAP When document being scanned, HWM Detect Hardware detects duplication prevention code in the document data.
003-702 RAP In simultaneous copying operation for both sides of original document, setting where magnification is different between Side1 and Side2 of the same document, is detected.
003-750 RAP Book Duplex-Insufficient Docs. Insufficient original sheets for a duplex book.
003-751 RAP Under PANTHER Capacity (Scan). Was below the PANTHER capacity in the Scan service (IIT sc).
003-752 RAP This status code is displayed if 600dpi cannot be scanned (DADF).
003-753 RAP This status code is displayed if over 300dpi cannot be scanned (DADF).
003-754 RAP S2X Recoverable Error. A ‘can recover?’ error was reported by the S2X.
003-755 RAP S2X Command Error. S2X returned a command error.
003-757 RAP This status code is displayed if over 400dpi cannot be scanned (DADF).
003-760 RAP Scan Settings Error. Read settings were incorrect.
003-761 RAP Incorrect Paper Tray Size. The paper size for the previously selected tray is different from the paper size that was selected with APS.
003-763 RAP Adjustment Chart Not Found. Error reading the contrast correction chart.
003-764 RAP Image Overlay Document Shortage. Only for B/W, not color.
003-780 RAP Scan Image Compression Error. Read image compression error.
003-795 RAP AMS Limit Error. When using the automatic magnification specification (AMS) it was outside the magnification range (25% ~ 400%) after the original was automatically detected.
003-930 Cannot Scan Over 300DPI RAP Due to insufficient DAM memory space, A3 original cannot be scanned with specified resolution. A4/B4 original can be scanned. 300dpi/400dpi/600dpi disabled with DADF Mix Duplex Mode Scan.
003-931 Cannot Scan Over 400DPI RAP Due to insufficient DAM memory space, A3 original cannot be scanned with specified resolution. A4/B4 original can be scanned. 400dpi/600dpi disabled with DADF Mix Duplex Mode Scan.
003-932 Cannot Scan Over 600DPI RAP Due to insufficient DAM memory space, A3 original cannot be scanned with specified resolution. A4/B4 original can be scanned. 400dpi/600dpi disabled with DADF Mix Duplex Mode Scan.
003-933 Cannot Scan Over 600DPI RAP Due to insufficient DAM memory space, A3 original cannot be scanned with specified resolution. A4/B4 original can be scanned. 300dpi/400dpi/600dpi disabled with DADF Mix Duplex Mode Scan.
003-934 Cannot Scan Over 400DPI RAP Due to insufficient DAM memory space, A3 original cannot be scanned with specified resolution. A4/B4 original can be scanned. 400dpi/600dpi disabled with DADF Mix Duplex Mode Scan.
003-935 Cannot Scan Over 600DPI RAP Due to insufficient DAM memory space, A3 original cannot be scanned with specified resolution. A4/B4 original can be scanned. 600dpi disabled with DADF Mix Duplex Mode Scan.
003-940 RAP This status code is displayed if the DAM Memory is insufficient.
003-942 RAP Document Size Error. The size of the original could not be automatically recognized.
003-944 RAP Image Repeat Count Fail. The image repeat count was incorrect, so images have been omitted.
003-946 RAP Copy Vertical/Horizontal Difference (APS). Without rotation the image would be truncated, but a paper size that cannot be rotated was selected.
003-947 RAP Replaced Original Count Error. The number of original sheets replaced by the user was less than the number of original sheets originally put into position.
003-948 RAP Replaced Original MismatchThe originals that have been put into position are different (original size, direction, or ACS color mode) from those before the replacement.
003-951 One Job Max Page Over Limit RAP Over the limit of pages being scanned in one job.
003-952 RAP Return Documents Color mismatch. The originals were replaced but the color of the originals replaced by the user was different.
003-955 RAP Documents Size Exchange Error. The function to prohibit mixed-size originals was selected but, when originals were added, originals of a different size or direction were detected.
003-956 RAP Documents Size Unknown Error. The platen was selected and the size of the original cannot be specified (only applies to APS).
003-963 RAP No Auto Paper Select Object Tray
003-965 RAP ATS/APS No Paper. There is no paper in the trays that can be selected with APS.
003-966 RAP AATS/APS No Destination Error. There are no trays that can be selected with APS.
003-967 RAP DADF APS No Destination.
003-968 RAP Punch Position Error. It is not possible to punch at the selected location.
003-969 RAP Punch Size Error. It is not possible to punch with the selected paper size.
003-971 RAP Duplication Restriction Code detected in original document while Duplication Restriction Code Detection Temporary Cancel Authorization user performs Scan job.
003-972 RAP Maximum Stored Page Over Flow. The number of original sheets exceeded the maximum number of sheets that can be stored.
003-973 RAP Every Direction DifferenceThe directions of the original and the image are different, and the image would be truncated if it isn't rotated, but it isn't possible to rotate.
003-974 RAP Next Original Specification All the originals that were put into position have been scanned.
003-976 FAX Line Memory Overflow (N up) RAP The number of SlowScan lines exceeds upper limt(65535) due to FAX 2 in one or Long Document expansion or Page Memory Full occurs.
003-977 RAP Document Mismatch (Multi Scan). The originals were replaced during consecutive page copying or duplex book scanning.
003-978 RAP Color Document Mismatch (Multi Scan).
003-980 RAP Staple Position Error. It is not possible to staple at the specified location.
003-981 RAP Staple Size Error. It is not possible to staple with the selected paper size.
003-982 RAP IITsc HDD Access Error. HDD was determined to be full during a collation job, destination storage job, or insertion job.
005-121 RAP DADF Feed Sensor ON Jam
005-122 RAP DADF Simplex/Side 1 Pre Reg Sensor ON Jam
005-123 RAP DADF Simplex/Side 1 Reg Sensor ON Jam. The Reg Sensor did not come on within a given time after the Pre Reg Sensor came on.
005-124 RAP DADF Lead Reg Sensor ON Jam. The Lead Reg Sensor did not come on within a given time after the start of reading (Reg motor ON).
005-125 RAP DADF Reg Sensor OFF Jam. The Lead Reg Sensor did not turn off within a given time after the start of reading (Reg Motor ON).
005-126 RAP DADF Out Sensor ON Jam. The Out Sensor did not come on within a given time after the start of reading (Reg Motor ON).
005-127 RAP DADF Out Sensor OFF Jam. The Out Sensor did not turn off within a given time after the Reg Sensor turned off.
005-128 RAP DADF Exit Sensor 1 ON Jam (Simplex Mode). In simplex mode, Exit Sensor #1 did not come on within a given time after the Out Sensor turned off.
005-129 RAP DADF Exit Sensor 1 OFF Jam (Simplex Mode). In simplex mode, Exit Sensor #1 did not turn off within a given time after the Out Sensor turned off.
005-130 RAP DADF Invert Sensor ON Jam (Duplex Mode). In duplex mode, the Invert Sensor did not come on within a given time after the Out Sensor came on.
005-133 RAP DADF Invert Sensor OFF Jam. In duplex mode, the Invert Sensor did not turn off within a given time after the Out Sensor turned off.
005-135 RAP DADF Pre Reg Sensor ON Jam (Invert). During an invert operation the Pre Reg Sensor did not come on within a given time after the start of the Feed Motor reverse revolution.
005-136 RAP DADF Reg Sensor ON Jam (Invert). During an invert operation the Reg Sensor did not come on within a given time after the Pre Reg Sensor came on.
005-137 RAP DADF Exit Sensor 2 ON Jam. During a reverse revolution expelling operation, Exit Sensor #2 did not come on within a given time after the start of the Feed Motor reverse revolution.
005-138 RAP DADF Exit Sensor 1 ON JamDuring a reverse revolution expelling operation, Exit Sensor #1 did not come on within a given time after Exit Sensor #2 came on.
005-139 RAP DADF Invert SNR off Jam.
005-141 RAP DADF Feed Sensor OFF Jam. The Pre Reg Sensor turned off before the Feed Sensor turned off.
005-142 RAP DADF Exit Sensor 1 OFF Jam (Duplex Mode). During a reverse revolution expelling operation, Exit Sensor #1 did not turn off within a given time after Exit Sensor #1 came on.
005-143 RAP DADF Exit Sensor 2 OFF Jam. Exit sensor #2 did not turn off within a given time after Exit Sensor #2 came on.
005-144 RAP DADF Too First Pre Reg Sensor ON Jam. The pre Reg Sensor came on before a given time due to original skew.
005-150 RAP DADF Feed Sensor OFF Jam (Perforated Original Mode). In perforated original mode, the Feed Sensor did not turn off within a given time after the Feed Sensor came on.
005-151 RAP DADF Pre Reg Sensor OFF Jam (Perforated Original Mode). In perforated original mode, the pre Reg Sensor did not turn off within a given time after the pre Reg Sensor came on.
005-152 RAP DADF Reg Sensor OFF Jam (Perforated Original Mode). In perforated original mode, the Reg Sensor did not turn off within a given time after the Reg Sensor came on.
005-153 RAP DADF Reg Sensor OFF Jam (Perforated Original Mode). In perforated original mode, the lead Reg Sensor did not turn off within a given time after the lead Reg Sensor came on.
005-154 RAP DADF Out Sensor OFF Jam (Perforated Original Mode). In perforated original mode, the Out Sensor did not turn off within a given time after the Out Sensor came on.
005-155 RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Simplex). In perforated original mode, Exit Sensor #1 did not turn off within a given time after Exit Sensor #1 came on (simplex).
005-156 RAP DADF Exit Sensor 1 OFF Jam (Perforated Original Mode) (Duplex). In perforated original mode, Exit Sensor #1 did not turn off within a given time after Exit Sensor #1 came on (duplex).
005-157 RAP DADF Invert Sensor OFF Jam (Perforated Original Mode). In perforated original mode, the Invert Sensor did not turn off within a given time after the Invert Sensor came on.
005-158 RAP DADF Exit Sensor 2 OFF Jam (Perforated Original Mode). In perforated original mode, Exit Sensor #2 did not turn off within a given time after Exit Sensor #2 came on.
005-160 RAP DADF Tray Lift Up Fail (Document Set) (Within Job). The originals were put into position and the Stack Height sensor did not come on within a given time after the tray began rising. Or, it was detected that the Bottom Sensor did not turn off. (Detected during run, stop, or purge.).
005-190 RAP DADF Feed Motor Logic Jam.
005-194 RAP Size Mismatch Jam on Slow Scan Mix Size. ‘Secondary scan mix’ was specified and it was detected that the size in the main scan direction was different from the width of the originals guide.
005-195 RAP Size Mismatch Jam on No Mix Size. It was detected that the originals have different sizes, but original size mix mode was not selected.
005-196 RAP Size Mismatch Jam on No Mix Size. It was detected that the second or later original sheet had a different size from that of the first original.
005-197 RAP Prohibit Combine Size Jam. A size that does not allow combining was detected.
005-198 RAP Too Short Size Jam. The originals could not be transported because the length was too short in the secondary scan direction. (When the leading edge of the original reached the Pre Reg Sensor the trailing edge had already passed the Feed Sensor.).
005-199 RAP Too Long Size Jam. Originals were detected that were longer than the secondary scan length that the DADF can transport.
005-275 RAP DADF RAM Fail. An error was detected in the DADF PWB RAM. (Checked when power is switched on.).
005-280 RAP DADF EEPROM Fail. A write error to DADF EEPROM or a communication error with EEPROM was detected.
005-281 RAP DADF Tray Lift Down Fail. The Bottom Sensor did not come on within a given time after the DADF tray began to lower.
005-282 RAP DADF Tray Lift Up Fail (No Document). During the initializing movement when no document had been put into position, the Bottom Sensor did not turn off within a given time after the tray began to rise.
005-283 RAP DADF Stack Height Sensor Logic Fail.
005-284 RAP DADF APS Sensor Logic Fail. There is a logical inconsistency among the outputs of APS Sensors 1 ~ 3.
005-302 RAP DADF Feeder Cover Interlock Open (Static).
005-303 RAP DADF Tray Interlock is open.
005-304 RAP Platen Interlock Open. During a DADF operation, the Platen Interlock opened.
005-305 RAP DADF Feeder Cover Interlock Open (Run). During a DADF operation the Feeder Cover Interlock opened.
005-306 RAP DADF Tray Interlock Open (Run). During a DADF operation the Tray Interlock opened.
005-308 RAP The DADF L/H Cover Interlock is open.
005-309 RAP DADF L/H Cover Interlock Open (Run). During a DADF operation the L/H Interlock opened.
005-906 RAP DADF Feed Sensor Static Jam. The Feed Sensor came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-907 RAP DADF Pre Reg Sensor Static Jam. The Pre Reg Sensor came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-908 RAP DADF Reg Sensor Static Jam. The Reg Sensor came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-909 RAP DADF Lead Reg Sensor Static Jam. The Lead Reg Sensor came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-910 RAP DADF Out Sensor Static Jam. The Platen Exit Sensor came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-911 RAP DADF Exit Sensor 1 Static Jam. Exit Sensor 1 came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-912 RAP DADF Exit Sensor 2 Static Jam. Exit Sensor 2 came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-913 RAP DADF Invert Sensor Static Jam. The Invert Sensor came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-914 RAP DADF No. 1/2/3 APS Sensor Static Jam. The DADF No. 1/2/3 APS Sensor came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-918 RAP DADF Invert Sensor 2 Static Jam. The DADF Invert Sensor 2 came on at one of the following times:1. Power on.2. Feeder Cover Interlock close.3. Platen Interlock close.
005-919 RAP DADF Tray Lift Up Fail (Document Set). The originals were put into position and the Stack Height Sensor did not come on within a given time after the tray began rising. Or, it was detected that the Bottom Sensor did not turn off. (Detected at a time other than run, stop, or purge.)
005-940 RAP DADF No Original Fail. It was detected that the original was removed.
005-941 RAP DADF Not Enough Document. After all originals were returned it was detected that the number of originals was insufficient
005-942 RAP DADF Tray Stack Over Fail.
010-311 RAP Heat Roll Temp Detection Circuit disconnection failure detected by Fuser Heat Roll STS.
010-319 RAP Fuser NC Sensor detection output - compensation output Difference circuit output failure is detected.
010-320 RAP Heat Roll High Temp failure detected by Fuser Center IR Sensor/Fuser Rear IR Sensor/Fuser Heat Roll STS. Temp for detection of High Temp failure is specified in NVM for each Temp Detection Device.NOTE: It is necessary to set NVM 744-506 to 0 in order to clear this failure.
010-321 RAP Fuser Nip or Release operation failure is detected.
010-322 RAP Heat Roll Temp Detection Circuit disconnection failure detected by Fuser Center NC Sensor.
010-323 RAP Heat Roll Temp Detection Circuit disconnection failure detected by Fuser Rear NC Sensor.
010-324 RAP Fuser NVM Fail.NOTE: It is necessary to set NVM [744-352] to 0 in order to clear this failure.
010-326 RAP Detection of continuous lighting failure of any of the Main Lamp1/Main Lamp2/Sub Lamp in Wait state. Detecting time is specified in NVM. Wait state Lamp/Heater is under control after Power ON, after Front Cover Interlock Close, after MSI Cover Interlock Close, after PH Drawer Interlock Close, and after Not Ready occurrence, so that Heat Roll/Belt is at the temperature ready to Print.
010-327 RAP Detection of continuous lighting failure of any of the Main Lamp1/Main Lamp2/Sub Lamp in Standby state. Detection time is specified in NVM. Standby state Heat Roll temperature is kept at Ready to Print temperature.
010-328 RAP Heat Roll High Temp/Low Temp failure is detected for a certain time with Fuser Lamp ON. Fail detection time is specified in NVM for each of During Print Process and Standby.
10-330 RAP Fuser Motor Fail. Fuser Motor rotation failure is detected.
010-342 RAP Decurler Cam Upper operation failure is detected.
010-343 RAP Decurler Cam Down operation failure is detected.
010-420 RAP Fuser Assembly Life Near End. The time for replacing the fuser assembly is getting close.
010-421 RAP Fuser Assembly Life End. It is time to replace the Fuser Assembly.
010-605 RAP Humidity Sensor operation failure is detected.
012-112 RAP Decurler In Sensor On Jam.
012-113 RAP Booklet In Sensor On Jam. The Booklet In Sensor did not come on within a given time after the Transport Entrance Sensor came on.
012-114 RAP Booklet In Sensor Off Jam 1.The Booklet In Sensor did not turn off within a given time.2.Before the previous set turned off the Booklet Folder Roll Exit Sensor, the first page of the next set turned off the Booklet In Sensor. (This prevents reverse rotation.)
012-115 RAP Booklet Folder Roll Exit Sensor On Jam. The Booklet Folder Roll Exit Sensor did not turn off within a given time after it came on.
012-125 RAP Gate Sensor On Jam
012-132 RAP Finisher Transport Entrance Sensor On Jam (Long).
012-142 RAP Buffer Path Sensor On Jam:The Buffer Path Sensor did not come on within a given time after the Transport Entrance Sensor came on. The Sensor did not come on within a given time after the start of a punch operation.
012-151 RAP Compiler Exit Sensor Off Jam. The Compiler Exit Sensor did not turn off within a given time after it came on.
012-152 RAP Compiler Exit Sensor On Jam
012-161 RAP Set Eject Jam. The Compiler Exit Sensor did not turn off within a given time after the start of an eject operation.
012-162 RAP Decurler In Sensor On Jam.
012-171 RAP Top Tray Exit Sensor On Jam 1. When punch mode is off: The Top Tray Exit Sensor did not come on within a given time after the Transport Entrance Sensor came on.2. In punch mode: The Top Tray Exit Sensor did not come on within a given time after the start of a punch operation.


012-172 RAP Top Tray Exit Sensor Off Jam. 1.The trailing edge of a sheet of paper did not turn off the Top Tray Exit Sensor within a given time after the leading edge of the same sheet of paper turned on the Transport Entrance Sensor. 2. The trailing edge of a sheet of paper did not turn off the top Tray Exit Sensor within a given time after the start of a punch operation.
012-180 RAP Booklet Folder Roll Exit Sensor Off Jam. The booklet folder roll exit sensor did not turn off within a given time after the booklet folder roll exit sensor came on.
012-211 RAP Stacker Tray Fail.The Stack Height Sensor did not turn off within 500 msec after the stack tray began to lower.
012-212 RAP Stacker Tray Upper Limit Fail. The Stacker had lifted up above the specified upper limit.
012-213 RAP Stacker Tray Lower Limit Fail. The Stacker Tray had lowered below the specified lower limit (Full Stack).
012-221 RAP Front Tamper Home Sensor On Fail. The Front Tamper Home Sensor did not come on within a given time after the Front Tamper Motor came on.
012-223 RAP Front Tamper Home Sensor Off Fail. The Front Tamper Home Sensor remained on after the Front Tamper Motor stopped.
012-224 RAP Rear Tamper Home Sensor Off Fail. The Rear Tamper Home Sensor remained on after the Rear Tamper Motor stopped.
012-225 RAP Booklet Tamper Home Sensor (F) On Fail. The Booklet Tamper Home Sensor (F) did not come on within a given time after the Booklet Tamper Motor (F) came on.
012-226 RAP Booklet Tamper Home Sensor (F) Off Fail. The Booklet Tamper Home Sensor (F) did not turn off within a given time after Booklet Tamper Motor (F) came on.
012-227 RAP Booklet End Guide Home Sensor Off Fail. The Booklet End Guide Home Sensor did not turn off within a given time after the Booklet End Guide Motor came on.
012-228 RAP Booklet End Guide Home Sensor On Fail. The Booklet End Guide Home Sensor (F) did not come on within a given time after the Booklet End Guide Motor came on.
012-229 RAP Booklet Tamper Home Sensor R On Fail. The Booklet Tamper Home Sensor (R) did not come on within a given time after the Booklet Tamper Motor (R) came on.
012-230 RAP Booklet Tamper Home Sensor R Off Fail. Booklet Tamper Home Sensor (R) did not turn off within a given time after Booklet Tamper Motor (R) came on.
012-243 RAP Booklet Knife Home Sensor On Fail.
012-246 RAP Booklet Stapler Fail:
012-247 RAP Side Reg. Sensor Off Fail. One or both of the Side Reg. Sensors did not turn off within the specified time.
012-260 RAP Eject Clamp Home Sensor On Fail. The Eject Clamp Home Sensor On did not come on within a given time after the Eject  Clamp Motor came on
012-261 RAP Booklet Knife Folder Sensor Fail.
012-263 RAP Finisher Rear Tamper Home Sensor On.
012-264 RAP Booklet Drawer Broken Fail. The Booklet Drawer Set Sensor was open when the Finisher Front Door Interlock was closed.
012-265 RAP Booklet Knife Home Sensor Off Fail. The Knife Home Sensor did not turn off within a given time after the Knife Solenoid came on.
012-266 RAP Booklet Compile No Paper Sensor Fail. The Booklet Compile No Paper Sensor is off at the start of a Booklet Staple job.
012-270 RAP Top Tray Offset Sensor On Fail
012-271 RAP Top Tray Offset Sensor Off Fail
012-282 RAP Eject Clamp Home Sensor Off Fail. The Eject Clamp Home Sensor did not turn off within a given time after the Eject Clamp Motor came on
012-283 RAP Finisher Set Clamp Home Sensor On Fail.
012-284 RAP Finisher Set Clamp Home Sensor Off Fail.
012-291 RAP Stapler Fail
012-295 RAP Finisher Stapler Move Position Sensor On Fail.
012-296 RAP Finisher Stapler Move Position Sensor Off Fail.
012-300 RAP Finisher Eject Cover Open (Compiler Cover).
012-302 RAP Finisher Front Door Interlock Open. The finisher front door is open.
012-307 RAP Booklet Drawer Set Fail. The booklet drawer has not been put into position.
012-320 RAP Punch Home Sensor On Fail. The Punch Home Sensor did not come on within a given time after the Punch Motor came on.
012-321 RAP Punch Home Sensor Off Fail. The Punch Home Sensor did not turn off within a given time after the Punch Motor came on.
012-322 RAP Punch Move Home Sensor Off Fail.
012-323 RAP Puncher Move Home Sensor On Fail. The Punch Move Home Sensor did not come on within a given time after the Puncher Move Motor came on.
012-330 RAP Decurler Cam Home Sensor Off Fail. The Decurler Cam Home Sensor did not turn off within a given time after the Decurler Cam Clutch came on.
012-332 RAP Decurler Cam Home Sensor On Fail. The decurler cam home sensor did not come on within a given time after the decurler cam clutch turned off.
012-334 RAP Download Mode Fail. After a download terminated in failure, when power is turned on, it will only come up in download mode.
012-335 RAP Booklet Sub CPU Communication Fail.
012-500 RAP Error detected while in data write to Finisher ROM (DLD system). Error detected while in write to Finisher-ROM (or MACS-ROM for BIZEN). ROM contents are deleted. Does not operate normally.
012-900 RAP Buffer Path Sensor Static Jam. The Buffer Path Sensor detected paper when the power was turned on, or when all interlocks were closed, or during an initialization operation.
012-901 RAP Decurler In Sensor static jam.
012-902 RAP Decurler Out Sensor static jam.
012-903 RAP Compiler Exit Sensor Static Jam. The Compiler Exit Sensor detected paper when the power was turned on, or when all interlocks were closed, or during an initialization operation.
012-905 RAP Compiler Tray No Paper Sensor Static Jam. The Compiler Tray No Paper Sensor detected paper when the power was turned on, or when all interlocks were closed, or during an initialization operation.
012-907 RAP Top Tray Exit Sensor Static Jam. The Top Tray Exit Sensor detected paper when the power was turned on, or when all interlocks were closed, or during an initialization operation.
012-920 RAP Gate Sensor static jam (Top Tray job)
012-932 RAP Gate Sensor static jam (Stacker job)
012-934 RAP Gate Sensor static jam (Stacker job).
012-935 RAP Transport Entrance Sensor static jam.
012-936 RAP Booklet In Sensor static jam.
012-949 RAP Puncher Waste Bin not detected.
013-902 RAP Booklet Compile No Paper Sensor Static Jam.The booklet compile no paper sensor detected paper when the power was turned on, or when all interlocks were closed, or during an initialization operation.
013-903 RAP Booklet Folder Roll Exit Sensor Static Jam.The booklet folder roll exit sensor detected paper when the power was turned on, or when all interlocks were closed, or during an initialization operation.
SquareFold® Trimmer Module Fault Codes
016-210 RAP Software Option Fail (HDD Does Not Exist). The HDD is not installed.
016-211 RAP Software Option Fail (System Memory Low Volume). There is insufficient system memory.
016-212 RAP SW Option Fail (Page Memory Low). One of the optional software functions cannot be supported due to insufficient page memory capacity.
016-213 RAP SW Option Fail (Printer CARD Does Not Exist). There is insufficient page memory.
016-214 RAP FAX_CARD Not Loaded or failure is detected when SW option function is set to Valid.
016-215 RAP SW Option Fail (JPEG PWB Does Not Exist) The JPEG PWB is not installed.
016-216 RAP SW Option Fail (Ext Memory Does Not Exist)The Extension Memory PWB is not installed.
016-217 RAP SW Option Fail (Controller ROM not Printer kit). The ESS ROM does not support the printer kit.
016-218 RAP Because PS Kit is not installed, XDOD functions cannot be fulfilled.
016-219 RAP License is required (Printer Kit). There is no license (the printer kit's SW key is not specified).
016-220 RAP S2X Unrecoverable Error. A fatal SX2 error was detected.
016-221 RAP S2X Communication Error. It was not possible to communicate with S2X.
016-222 RAP S2X Self-Diag Error. An error occurred during S2X self-diagnosis.
016-223 RAP SS2X SDRAM Error.
016-224 RAP S2X PCI Reg Error. S2X had a problem accessing its internal PCI space.
016-225 RAP S2X ROM CheckSum Error. S2X failed its ROM checksum test.
016-226 RAP S2X IIT Connection Error. S2X could not detect the video clock that it receives from IIT.
016-227 RAP S2X DDR Error. S2X failed its internal DDR memory write/read test.
016-228 RAP S2X Image Processing Error.
016-229 RAP SW Option Fail (User Interface-UI Does Not Exist) The Extension Memory PWB is not installed.
016-230 RAP SW Option Function not achieved. PS-ROM loaded with "SW Key: PS Image Log Kit" Invalid.
016-231 RAP SW Option Function not achieved. SW option cannot be enabled due to Ama+toto Board failure/Not Loaded.
016-232 RAP MRC HW Initialize Error. Error occurs while high-compression board is being initialized.
016-233 RAP SW option function not achieved. SW option function cannot be enabled due to USB host failure/Not loaded.
016-240 RAP High-compression PDF Board (S2X) NVM CheckSum Fail.
016-310 RAP SSMM Job Log Full. Job log file is not obtained from external application (AWAYS) and the files over specified limit (280 files) are stored.
016-311 RAP The scanner was not detected.
016-312 RAP SW Option Function not achieved. “Paper Security Kit" cannot be implemented because HighbridWaterMark detection hardware is not installed.
016-313 RAP SW Option(Paper Security Kit) is not set to Enable. When "HighbridWaterMark detection hardware Not Loaded" is detected while SW option function is set to Enable(Valid).
016-314 RAP SW Option Fail (HybridWaterMark Not Exist). While SW option function is enabled, simultaneous duplex scanning with 2 HWM boards (for Side1 and Side2) is conducted using the combination of DADF:PF1.5/IIT:PF1-BW. When reproduction limitation code is detected, the function is reflected only on page for which the code is detected.
016-315 RAP NIIT Interface Fail. An error was detected in the I/F between the scanner and the main chassis.
016-316 RAP Page Memory is Not Detected. It was detected that the page memory (standard) for the scanner portion was not installed.
016-317 RAP Page Memory Broken-Standard. An error was detected with the page memory (standard) for the scanner portion.
016-318 RAP Page Memory Broken-Option. An error was detected with the page memory (option) for the scanner portion.
016-321 RAP FAX-related error at startup. With SysCheckFax(), ERROR is returned. If PFNOTEXIST is returned, M/C configuration is regarded as without FAX.
016-322 RAP JBA Account Full. The JBA accounting data is full.
016-323 RAP B-Formatter task fatal error. Unrecoverable error is detected within Fax Send image conversion area B-Formatter task from extended mailbox in "Multi-Send using Job Flow Indication" or "UI Multi-Send".
016-324 RAP Scheduled ImageOverwrite. Issued by SysCon when it comes to the setting time of Scheduled Image Overwrite execution.
016-330 RAP Cont SystemMemory Diag Fail-1. Capacity of Slot1 loaded memory is out of spec.
016-331 RAP Cont SystemMemory Diag Fail-2. Capacity of Slot2 loaded memory is out of spec.
016-332 RAP Cont SystemMemory Diag Fail-3. Capacity of Slot3 loaded memory is out of spec.
016-335 RAP Cont Program ROM Diag Fail-1. Program ROM2 CheckSum is not correct.
016-336 RAP Cont Program ROM Diag Fail-2. Program ROM1 CheckSum is not correct.
016-337 RAP Cont Program ROM Diag Fail-3. Program ROM2 Write Command failure.
016-338 RAP Cont FontROM Diag Fail-1. OnBoard loaded Font ROM ID is out of spec.
016-339 RAP Cont FontROM Diag Fail-2. Slot1 loaded Font ROM ID is out of spec.
016-340 RAP Cont FontROM Diag Fail-3. Slot2 loaded Font ROM ID is out of spec.
016-341 RAP Cont Font ROM Diag Fail-4. Slot2 loaded Font ROM CheckSum is not correct.
016-342 RAP Cont RTC Diag Fail. RTC time range is out of the specified range. (Ex 13 month 36 day) Time does not go on.
016-345 RAP Cont NV-Memory Diag Fail. Initial address data is 0x00.
016-347 RAP Cont PageMemory Diag Fail. Slot2 loaded memory capacity is out of spec.
016-348 RAP Cont PageMemory Fail-2. W/R/V test error for Page Memory.
016-350 RAP Cont SEEP-ROM Diag Fail-1. Product ID cannot be obtained.
016-351 RAP Cont SEEP-ROM Diag Fail-2. W/R/V Test Error.
016-360 RAP Cont UI Diag Fail-1. PCI Config space W/R/V test error.
016-362 RAP Cont UI Diag Fail-2. UI Communication error. VRAM W/R/V test error. If Long Boot Mode is entered, Command/Status line would be normal.
016-363 RAP Cont JPEG Card Diag Fail. Cont LyraCard Fail. PCI Config space W/R/V test or internal register W/R/V test error.
016-364 RAP Cont USB2.0 Host Diag Fail. Cont LyraCard Fail. PCI Config space W/R/V test or internal register W/R/V test error.
016-365 RAP Cont USB2.0 Device Diag Fail. Cont LyraCard Fail. PCI Config space W/R/V test or internal register W/R/V test error.
016-366 RAP Cont HDD Diag Fail-1. Cont LyraCard Fail. IDE Controller check error (ideDrv equivalent).
016-367 RAP Cont HDD Diag Fail-2. HDD W/R/V test error.
016-368 RAP Cont Torino Diag Fail. PCI Config space W/R/V test or internal register W/R/V test error.
016-369 RAP Cont S2X Board Diag Fail. PCI Config space W/R/V test error.
016-370 RAP Cont Rendering engine diagnosis Fail. Error is detected in rendering engine diagnosis.
016-371 RAP Cont USB1.1 Host Diag Fail. Error is detected in USB1.1Host diagnosis (Communication with FaxCard cannot be established).
016-400 RAP 802.1x Authentication error (Wrong user name or wrong password). User name or password set for M/C is not correct. Switch setting of "Authentication device" physically network-connected with M/C is not correct.
016-401 RAP 802.1x Authentication method mismatch (M/C authentication method not supported by authentication server). Fail signal informing that authentication method set for M/C cannot be processed is received from "Authentication device" physically network-connected with M/C.
016-402 RAP 802.1x Authentication timeout (No response signal received from "Authentication device").
016-403 RAP 802.1x Authentication certificate mismatch. Root certificate, Authentication Server certificate, is not stored in M/C or not consistent.
016-404 RAP 802.1x Other authentication error. Internal error occurs with 802.1xSupplicant function of M/C. Illegal protocol signal is received from authentication server.
016-405 RAP Certificate data base file failure. Header abnormal/size abnormal detected when certificate data base file being read during system startup.
016-450 RAP SMB Host Name Duplicated. There is another PC with the same host name on the network.
016-453 RAP Dynamic DNS - IPv6 Address Dynamic Update failure. Failed to update IPv6 address and host name to DNS Server.
016-454 RAP DNS Renewal Failure of Dynamic. An IP address could not be obtained from DNS.
016-455 RAP SNTP Server Time-Out There was no response from the SNTP server within the given time (60 seconds).
016-456 RAP SNTP Time Asynchronous. A message was received that was not synchronized with the standard synchronization source from the SNTP.
016-461 RAP Limitation of creation of new job due to Image Log transfer suspension in process. When system data "Image log transfer guarantee level" is set to "High", limitation of creation of new job is activated due to Image Log transfer suspension.
016-500 RAP Error detected while in data write to Cont-ROM. (DLD system). Error detected while in write to Controller-ROM. ROM contents are deleted. Does not operate normally.
016-501 RAP Error detected while in data write to S2X-ROM (DLD system). Error detected while in write to S2X-ROM. ROM contents are deleted. Does not operate normally. .
016-502 RAP Error detected while in data write to any of Cont/S2X/IISS/DADF/IOT/Fin/FaxCard(PJL system). Error detected while in write to any of ROM. The ROM contents are deleted. Does not operate normally.
016-503 RAP SMTP Server Address Resolution Fail. The SMTP server name was not correct when sending mail.
016-504 RAP POP Server Address Resolution Fail. The POP3 server name was not correct when sending mail.
016-505 RAP POP Authentication Fail. There was a failure logging in to the POP3 server when sending mail.
016-506 RAP ImageLog HDD Full. While system data "Log Image creation guarantee level" is set to "High", Disk Full in Log Image storage place occurs. (While the job other than Copy/Scan job is in process.)
016-507 RAP ImageLog Send Fail01. While system data "Auto Transfer Setting" is set to "Job by Job Transfer", job cannot be continued due to Log Image transfer failure.
016-508 RAP ImageLog Send Fail02. While system data "Auto Transfer Setting" is set to "Job by Job Transfer", job cannot be continued due to Log Image transfer failure.
016-509 RAP ImageLog No Send Rule01. While system data "Auto Transfer Setting" is set to "Job by Job Transfer", job cannot be continued due to transfer rule not registered(saved).
016-510 RAP ImageLog No Send Rule02. Transfer failure due to transfer rule not registered (not saved).
016-511 RAP ImageLog Invalid Send Rule01. While system data "Auto Transfer Setting" is set to "Job by Job Transfer", job cannot be continued due to transfer rule Illegal.
016-512 RAP ImageLog Invalid Send Rule02. Transfer failure due to Transfer Rule Illegal.
016-513 RAP SMTP server reception error. (SMTPERR_CONNECT_RESP_FAILED).
016-514 RAP XPS Error. Invalid Schema, parameter error, XPS file breakage or XPS decomposer internal error occurs while in XPS Bridge processing.
016-515 RAP XPS Short of Memory. Memory shortage is detected in XPS Bridge processing.
016-516 RAP XPS PrintTicket description error. Print Ticket included in XPS Document is "Grammar is not supported by the M/C " or "Print request content is not supported by the M/C".
016-517 RAP PS Booklet Illegal Color Mode Change. PSDecomp detects change of ProcessColorModel or resolution/bi-tone/con-tone parameter while in interpretation of job with Booklet designation.
016-518 RAP Simultaneous designation of WaterMark for PS Booklet.
016-520 RAP MRC HW Job Error. Error occurs while high-compression board is in use.
016-522 RAP LDAP-SSL Authentication error 112(Cannot acquire Client Certificate.) LDAP Server SSL Authentication error. SSL Client Certificate cannot be acquired.
016-523 RAP LDAP-SSL Authentication error 113(Server Certificate data is illegal.)
016-524 RAP LDAP-SSL Authentication error 114(Server Certificate is before expiration date.)
016-525 RAP LDAP-SSL Authentication error 116(Server name and certificate are inconsistent.) LDAP Server SSL Authentication error . Server Certificate is expired.
016-526 RAP LDAP-SSL Authentication error 116(Server name and certificate are inconsistent.) LDAP Server SSL Authentication error. Server name and certificate are not consistent each other.
016-527 RAP LDAP-SSL Authentication error 117(SSL Authentication internal error ).
016-529 RAP Remote Download Server Time Out. No response is made within specified time (60 seconds) after connected to Remote Download Server.
016-533 RAP Kerberos Authentication Protocol error (37 ). Difference between Device and Kerberos server clock exceeds the limit of clock queue on Kerberos side.
016-534 RAP Kerberos Authentication Protocol error (41,42 ).
016-535 RAP FW Update file not on Remot Download Server. Designated FW Update file (Download Image file) does not exist on Remote Download Server.
016-536 RAP Remote Download Server Name Resolution error. Host name (=Server name) solution fails at the timing of DNS access before connection to Remote Download Server. DNS Library Call error .
016-537 RAP Remote Download Server Connection error. Port of Remote Download Server connected is not open.
016-538 RAP Remote Download file Write error to HDD. Cannot write to HDD normallythe FW Update file obtained from Remote Download Server.
016-539 RAP Kerberos Authentication Protocol error (Other). Program internal error occurred.
016-543 RAP Authentication Agent error “REALM_UNKNOWN”. Designated realm/domain disappeared from ApeosWareAuthenticaton Agent. (After realm name has been obtained by Device, domain has been deleted manually by ApeosWare Authentication Agent).
016-545 RAP Authentication Agent error CLOCKSKEW_ERR. Clock skew error occurred in Authentication . ApeosWare Authentication Agent and ActiveDirectory time (clock) is out of synchronization with Kerberos ClockSkew upper limit being set in Active Directory.
016-546 RAP Authentication Agent error ACCESS_DENIED. General user tried to acquire user information other than his own. (GetUserInformation Method only). User name included in http WWW-Authorization and included in GetUserInformation Method request message are different each other.
016-548 RAP Authentication Agent error UNREGISTERED_DEVICE. The information for the device which has performed Authentication operation does not exist in database. (GetUserInformation method only) Device is not registered in ApeosWare Authentication Agent.
016-553 RAP Authentication Agent error VERSION_MISMATCH. Cannot understand Version information described in SOAP Header. ApeosWare Authentication Agent does not support device interface version.
016-554 RAP Authentication Agent error CONFIGRATION_ERROR. Failed to check the existence(identity) of the user who is designated by Authentication error . Domain user reference login name or reference password for ApeosWare Authentication Agent Domain is illegal.
016-555 RAP Authentication Agent error SERVICE_ISNOT_WORKING. Timeout for connection to Authentication server. ApeosWare Authentication Agent cannot be connected to database or Active Directory.
016-556 RAP Authentication Agent error SERVICE_IS_PROCESSING. Database processing timeout. Database, being connected to ApeosWare Authentication Agent has overload error
016-557 RAP Authentication Agent error INTERNAL_ERROR. Other error occurred in Authentication . ApeosWare Authentication Agent internal error.
016-558 RAP Authentication Agent error MISC_ERR. M/C received unknown error from ApeosWare Authentication Agent.
016-559 RAP Remote Download Parameter error. System data required for Remote Download has illegal value setting.
016-560 RAP Authentication Agent communication error. Communication error between M/C and ApeosWare Authentication Agent occurred.
016-562 RAP Authentication Agent error *Duplication of ID found in ICCG external Authentication. More than one entry with same IC Card data found on ActiveDirectory or Authentication Agent temporary user DB.
016-563 RAP Cannot continue the job due to Image Expansion Kit memory insufficiency. Image Expansion Kit memory insufficiency occurs while system data log image creation guaraantee level is set to "High".
016-564 RAP Remote Download Server Authentication Failed. Authentication error informed by Server when Remote Download Server being accessed.
016-565 RAP Backup Restore Error. Authentication error informed by Server when Remote Download Server being accessed.
016-566 RAP Backup Restore Condition Error. FW Download File of the version same as that of M/C not found at Backup operation. Cannot restore because M/C config is not consistent between Restore and Backup operations.
016-567 RAP Backup Capacity Full. Backup place storage capacity insufficient.
016-568 RAP Backup Restore Failed. Backup place storage capacity insufficient. HDD access error. USB Memory access error. Backup file broken found at Restore.
016-569 RAP Authentication Agent error 569.
016-570 RAP XPIF Memory insufficient. XPIF Parther detects memory insufficiency during Job Ticket Interpretation operation.
016-571 RAP XPIF Parameter Mismatch . Decomposer detects the Job Ticket designation which does not meet Device specification.
016-572 RAP XPIF Media Conversion Error . Decomposer detects the following: Paper attributes designated by Job Ticket cannot be identified as Device-supported paper (Size, Paper type, Paper color).
016-573 RAP XPIF Interpretation Error. XPIF Parather receives and processes the Job Ticket having uninterpretable syntax.
016-574 RAP FTP Scan Host Name Resolution Failure. Host name (=Server name) resolution failed when DNS being accessed before FTP Server is connected. DNS Library Call error .
016-575 RAP FTP Scan DNS Server Not Set. DNS Sever Not Set is detected before connection to FTP Server. DNS Library Call error.
016-576 RAP FTP scan connection problem with the DFE. Connection to the FTP service on the DFE failed.
016-577 RAP FTP service problem with the DFE. Connection to the FTP service on the DFE failed.
016-578 RAP FTP Scan login name or password error. USER./PASS command failed in M/C after FTP Server connected. Problem with login name or password.
016-579 RAP FTP Scan image storage place problem. After connected to FTP, the data fails to move to RepositoryPath. Scan Image Data Storage Place has a problem.
016-580 RAP FTP scan Server File Name/ Folder Name acquisition failure. NLST command failed when server file/folder name is obtained after FTP server connected.
016-581 RAP FTP Scan File Name /Folder Name suffix is over the limit. File Name/folder Name suffix limit exceeded while file name/folder name determination is in process after connected to FTP server.
016-582 RAP FTP Scan File creation failure. Failed to create File in file creation process in Server after being connected to FTP Server.
016-583 RAP FTP Scan Lock Folder creation failure. Failed to create lock folder during lock folder creation process in Server after being connected to FTP Server.
016-584 RAP FTP Scan Folder creation failure. Failure to create Folder when trying to create folder in server after connected to FTP server.
016-585 RAP FTP Scan File deletion failure. Failed to delete a file in Server after connected to FTP Server.
016-586 RAP FTP Scan Lock Folder deletion failure. Lock folder deletion failed in server after FTP server connected.
016-587 RAP FTP Scan folder deletion failure. Folder deletion failure while in folder deletion process in server after connected to FTP server.
016-588 RAP Failure to write data to FTP scan server. Data Write failure to server after connected to FTP server.
016-589 RAP Data read failure from FTP server. Scanner (PC storage) data transferred to FTP. After connected to FTP server, FTP server data Read failed.

[dastin]

часть вторая

016-590 RAP Data reading failure from FTP server. Scanner (PC storage) data transferred to FTP. After connected to FTP server, file cannot be stored due to file name duplication, where "Job stopped (not stored)" is set.
016-591 RAP FTP scan filing policy Illegal. Filing policy Illegal (when Additional is selected) detected after connected to FTP server.
016-592 RAP NEXTNAME.DAT file access error in FTP. In FTP transfer with Scanner (PC storage), NEXTNAME.DAT file access error occurs after FTP server connected.
016-593 RAP FTP Scan internal error. Redirector internal error occurs after connected to FTP server.
016-594 RAP FTP Scan TYPE command error (Network error ).
016-595 RAP FTP Scan PORT command error. PORT command failed after FTP server connected. (Network error )
016-596 RAP FTP Scan CDUP command error. CDUP command failed after FTP server connected. (Network error)
016-597 RAP Operation (Processing) suspended due to existence of same name file for FTP Scan. File/Folder with same name found after FTP server connected, and then M/C suspended. (CreditMutuel Specification)
016-598 RAP Email message size over limit. In Page Split, mail data size for one page exceeds "Max. message size" of system data.
016-599 RAP Email message size over limit. In Page Split, mail data size for one page exceeds "Max. message size" of system data.
016-600 RAP KO Authentication Locked. The number of consecutive KO authentication errors reached the number specified in system data: ‘Maximum Consecutive KO Authentication Errors (DC131 [700-563])’.
016-601 RAP Illegal Access Detection. The number of authentication errors (including CO/KO) within a given time reached the number specified in system data: ‘Maximum Number of Authentication Errors (DC131 [700-564])’.
016-700 RAP Password is under minimum length. Job with password that does not meet the minimum number of password digits is received. To be designed such that the minimum number of password digits for Security Print and Authentication Print can be set and a job with password having less digits than required is not stored.
016-701 RAP Out of ART EX Memory. Insufficient memory was detected while using ART EX.
016-702 RAP Out of Page Buffer. Even a single page could not be compressed. It was detected that the print page buffer was insufficient.
016-703 RAP Email to Invalid Box. E-mail was received that specified a security box that was not enabled or that was not valid.
016-704 RAP Mailbox is Full. The full condition was detected when accessing the HD.
016-705 RAP Secure Print Fail. Secure storage was not possible without the HDD. A failure occurred when registering a securely printed document.
016-706 RAP Max. User Number Exceeded. It was detected that the HDD was full because the maximum number of users for secure printing was exceeded.
016-707 RAP Sample Print Fail. A sample print was not possible because the HDD was not installed.
016-708 RAP HD Full by Annotation/Watermark Image. The job terminated because the full condition was detected during HD storage of an annotation or watermark image.
016-709 RAP ART EX Command Error. An ART EX command error occurred during PLW processing.
016-710 RAP Delayed Print Fail.
016-711 RAP In mailing iFAX and instructions for forwarding, the transmission module (Redirection) tried to send to the network, data whose size is over the system data ‘the upper limit of Scan to Email data size.’
016-712 RAP Under PANTHER Capacity (I-Formatter).
016-713 RAP Security Box Password Error. Password composition failed during storage to a security box.
016-714 RAP Security Box is not Enabled. During storage to a security box the security box was not enabled.
016-715 RAP ESCP Form Invalid Password. When ESCP form is used, job is aborted because designated password is not correct.
016-716 RAP TIFF Data Overflow. A TIFF file could not be spooled because the capacity of the HDD was exceeded.
016-717 RAP Fax/iFax Send Result Not Found. Tried to create "UnSend Report" or "Monitor Report" but could not create because "Send Result Information" are not stored in M/C Memory/HDD. iFAX document Send exceeding Partition C capacity (2GB or 4GB) causes HDD Full, resulting in "iFax Send Result Information" storage failure. 200 or more jobs done after Report Output designation job completion and "iFax Send Result Information" are overwritten.
016-718 RAP Out of PCL6 Memory. Insufficient memory was detected when using PCL6.
016-719 RAP Out of PCL Memory. Insufficient memory was detected when using PCL.
016-720 RAP PCL Command Error. A PCL command error occurred during PCL processing.
016-721 RAP Other Error. An unexpected error occurred during print processing
016-722 RAP Job Cancel by Staple Position NG. A job was cancelled because the staple position was impossible.
016-723 RAP Job Cancel by Punch Position NG. A job was cancelled because the punch position was impossible.
016-724 RAP Complex Position Error of Staple and Punch.
016-725 RAP B-Formatter Library Image Conversion Error. While scan document stored in Mailbox is being sent to Facsimile device by use of M/C Job Flow function, conversion of Mailbox data to Facsimile data failed.
016-726 RAP PDL Auto Switch Fail. The print language could not be automatically selected when the print mode specification was ‘automatic’.
016-727 RAP 0-page document unstorable to MailBox. P-Formatter tries to store 0 page document in MailBox, but 0 page document cannot be stored. Job is cancelled.
016-728 RAP Unsupported TIFF Data. An unsupported tag was included in a TIFF file.
016-729 RAP TIFF Data Size too Big. A TIFF file could not be printed because the number of colors or resolution exceeded the upper bound for the permitted range.
016-730 RAP Unsupported ART Command. A command that is not supported by ART IV was detected.
016-731 RAP Invalid TIFF Data. Printing was not possible because the TIFF data was truncated.
016-732 RAP Form Not Registered. The decomposer detected that the specified form was not registered.
016-733 RAP Destination Address Resolution Error.
016-734 RAP Simple Transmission report invocation error. An error occurred while outputting a simple destination address result report.
016-735 RAP Updating Job Template. It decided to print the ‘Job Template List’ while updating a job template.
016-736 RAP Remote directory lock error. Lock directory creation failed.
016-737 RAP Remote lock directory remove error. Lock directory deletion failed.
016-738 RAP PS Booklet Print Output Paper Size is illegal.
016-739 RAP Mismatch between PS Booklet Doc and Output Paper
016-740 RAP PS Booklet Output Tray is incorrect.
016-741 RAP Download Mode NG. By SysData: 700-420=1, Download Inhibit detected but Download Mode transfer is disabled because some job still remains. M/C detects "M/C is in user operation", so M/C does not go to Download Mode. (One minute from Panel operation end, it becomes "User operating....."
016-742 RAP Download Data ProductID Error. ProductID sent in Download data does not match ProductID(SysData: 700-421 to 700-428) stored in SEEP-ROM.
016-743 RAP Download Data Model Mismatch. -ModelName obtained from attached IISS/DADF/IOT/FaxCard/Finisher does not conform to ModelName included in each firmware CDI header in download file. In Controller, "ModelName obtained from currently attached ROM header" and "ModelName in download file" are compared. Exception - With MACS of Kutani IOT/Bizen, ModelName is not checked due to old I/F specification. In downloading, panel type (HB or FCW) connected to the device does not conform to panel type (HB or FCW) included in Controller firmware CDI header in download file.
016-744 RAP Download Data Checksum Error.
016-745 RAP XPJL fatal error in downloading (Occurs after XPJL recognizes received data is downloaded data).
016-746 RAP Unsupported PDF File.
016-747 RAP Insufficient memory capacity in drawing annotation image. The condition with Varenne is as follows, however, it will not be described in the instruction manual due to variation with memory condition
016-748 RAP HD Full. The full condition was detected during HD access.
016-749 RAP PJL Syntax Error. A syntax error was detected in a XPJL or PJL command.
016-750 RAP PDF print job ticket description error. When printing is requested with application used by user for sending PDF directly such as "ContentsBridge2005", print job ticket sent with PDF is received by this M/C and print job ticket data are "Grammar inapplicable to this M/C" or "Print request content inapplicable to this M/C".
016-751 RAP PDF Error. A syntax error, usage of an undefined command, parameter error, corrupted PDF file, or PDF decomposer internal error occurred during PDF bridge processing.
016-752 RAP PDF Short of Memory. It was detected that there was insufficient memory during PDF bridge processing.
016-753 RAP PDF Password Mismatched. The password specified on the UI panel and the password specified in XJPL (specified by the contents bridge) did not agree when processing a PDF file that was password protected.
016-754 RAP PDF LZW Not Installed. A PDF file that used LZW compression technology was processed by the PDF bridge when the ‘Contents Bridge Expansion Kit’ was not installed.
016-755 RAP PDF Print Prohibited. A PDF file for which it had been specified that printing was prohibited was processed.
016-756 RAP Auditron-Prohibit Service. The use of this service is prohibited.
016-757 RAP Auditron-Invalid User. A user account is invalid.
016-758 RAP Auditron-Disabled Function. A function cannot be used due to lack of rights or permission.
016-759 RAP Auditron-Reached Limit. The upper bound to the number of pages that can be copied was reached.
016-760 RAP PS Decompose Failure. An error occurred during postscript (option) processing.
016-761 RAP FIFO Empty. Image expansion error (FIFO empty error).
016-762 RAP Print LANG Not Installed. A function that is not installed (such as a print language or print utility) was specified.
016-763 RAP POP server is not found (When server is connected).
016-764 RAP SMTP Server Connect Error. It was not possible to connect to the SMTP server.
016-765 RAP SMTP Server HD Full. It was not possible to send mail because the HDD capacity of the SMTP server was full.
016-766 RAP SMTP Server File System Error. An error occurred in the SMTP server.
016-767 RAP Invalid E-mail Address. It was not possible to send because the mail address was wrong.
016-768 RAP Invalid Sender Address. It was not possible to connect to the SMTP server because the mail address of this equipment was not correct.
016-769 RAP SMTP Server Unsupported DSN. The SMTP server does not support path verification (DNS).
016-770 RAP Inhibition of Direct Fax job with System Data setting. The direct fax function is cancelled by NVM. Job history (UI,Report,CWIS,SSMI-using application).
016-771 RAP Scan Data Repository ERR. The scan data repository address cannot be obtained with the CentreWare scan service.
016-772 RAP Scan Data Repository ERR. The scan data repository address cannot be obtained with the CentreWare scan service.
016-773 RAP Invalid IP Address. The IP address of this equipment is not specified correctly.
016-774 RAP HD Full-Compression Convert. Compression and conversion processing is not possible because there is insufficient HDD capacity.
016-775 RAP HD Full-Image Convert. Image conversion processing is not possible because there is insufficient HDD capacity.
016-776 RAP Image Convert ERR. An error occurred during image conversion processing.
016-777 RAP HD Access ERR-Image Convert. An error occurred in the HDD during image processing.
016-778 RAP HD Full-Scan Image Convert. Scan image processing was interrupted because the HDD capacity was exceeded.
016-779 RAP Scan Image Conversion Error. An error occurred during scan image conversion processing.
016-780 RAP HD Access ERR-Image Convert. An error occurred in the HDD during scan image conversion processing.
016-781 RAP Scan Server Connect ERR. The CentreWare scan service could not connect to the server to send a file.
016-782 RAP Scan Server Login ERR. The CentreWare scan service could not log into the server to send a file.
016-783 RAP Invalid Server Path. The CentreWare scan service could not find the specified server path to send a file.
016-784 RAP Server Write ERR. An error occurred when writing to the server with the CentreWare scan service.
016-785 RAP Server HD Full. The CentreWare scan service could not send a file because the HDD of the server had insufficient capacity.
016-786 RAP HD Full-Scan Write ERR. It was not possible to write a file while using the scan function because the HDD capacity was insufficient.
016-787 RAP Invalid Server IP ADD. The server address specified in a job template was wrong.
016-788 RAP Retrieve to Browser Failed. The retrieval of a file from a web browser failed.
016-789 RAP HD Full-Job Memory. Processing was interrupted because the required HDD capacity to process mail was exceeded.
016-790 RAP The number of e-mail fragment per destination exceeds "Max. number of fragment" of System Data in Page Division and MessagePartial Division.
016-791 RAP File Retrieve Fail. There was an error in obtaining a file.
016-792 RAP Specified Job Not Found. The job log for a job specified in the panel could not be obtained when outputting an aggregate report by job.
016-793 RAP MF I/O HD Full. The HDD capacity was insufficient.
016-794 RAP Media Reader: Media No Insert.
016-795 RAP Media Reader: Format Error.
016-796 RAP Document insert operation error.
016-797 RAP Media Reader: Image File Read Error.
016-798 RAP No Trust Marking Option. When the decomposer called the S-image library the error of no HDD was returned.
016-799 RAP Print Instruction Fail. A print parameter was incorrect.
016-940 RAP After the start of a job with Duplex Output selected, a difference was detected in size between side 1 and side 2.
016-941 RAP After the start of a job with Booklet selected, mixed-in-size/orientation pages with images were detected.
016-942 RAP As a result of deletion of a page for which Duplex was selected, a difference was detected in size between side 1 and side 2.
016-943 RAP As a result of insertion of a doc/divider after a page for which Duplex was selected, a difference was detected in size between side 1 and side 2.
016-944 RAP It was found that docs were merged, where specified was connection of docs including the cover with an image or a doc with a divider.
016-945 RAP A document unavailable for duplex print was inserted after a document for which Duplex was selected.
016-946 RAP A document or a divider was inserted after the cover or divider page.
016-647 RAP After the start of a job with APS Doc selected or with APS set up, it was found that there were no trays loaded with paper of sizes for Auto Paper Selection.
016-648 RAP Though a job was started with Booklet selected, it was discontinued because it had the cover with an image, a divider or a blank page.
016-949 RAP After specifying page connection, the user inserted a doc different in size/orientation from the page to be processed.
016-981 RAP A failure in access to HDD
016-982 RAP HDD Access Error 2. It was determined that the HDD was full during a collation job, destination storage job, or divided job.
016-983 RAP Disk Full occurs in Log Image memory space when Log Image Creation Guarantee Level is set to "High" in system data. (when in processing of Copy\/Scan job.)
018-400 IPSEC Error (Configuration Mismatch)
018-500 CA Message Receiver Boot Error(S_cert lost)
018-501 CA Server Connection Error
018-502 Login failure in SMB
018-503 CA Message Receiver Timeout
018-504 CA SessionID Mismatch
018-505 SMB-DOS Protocol Error 1-005
018-506 CA FieldID Mismatch
018-507 CA Credential Error
018-508 CA Server Fatal Error
018-509 Template Parameter Conflict
018-510 Host Name Solution Error in BMLinkS
018-511 DNS Server Not Set in BMLinkS
018-512 Service Connect Error in BMLinkS
018-513 BMLinkS Service Not Found
018-514 BMLinkS Access-Right-Violation
018-515 BMLinkS Storage-Access-Error
018-516 BMLinkS Unsupported-Attribute
018-517 BMLinkS Storage-Full
018-518 BMLinkS Operation-Not-Available
018-519 BMLinkS Unknown-Error
018-520 Internal Eerror in BMLinkS Scan
018-521 Request Ssend Failure in BMLinkS
018-522 Response Rreceive Failure in BMLinkS
018-523 Image Send Ffailure in BMLinkS
018-524 Invalid Device Network Setting
018-525 HDD Full or HDD Access Error
018-526 CUI Scan: While Job Template is Being Poled
018-527 JT Monitor Internal Error
018-528 Soap Request Error
018-529 Duplicate Scan Request
018-530 Authentication Error
018-531 Other Error at CUI Scan Job Start
018-532 CUI Scan Job Generation Fails
018-543 Shared Name Error in SMB Scan Server
018-547 Number Restriction Over of SMB Scan Users
018-556 HTTP Server Script Error
018-557 HTTP Invalid Char in Filename
018-558 HTTP File Not Found
018-559 HTTP File Duplication Fail
018-560 HTTP Server Login Fail
018-561 HTTP Server Not Found
018-562 HTTP Client Error
018-563 HTTP Server Error
018-564 HTTP Server Error
018-565 Proxy Name Solution Error in HTTP
018-566 Server Connect Error in HTTP
018-567 HTTP Server Access Fail
018-568 HTTP Server SSL Access Fail
018-569 HTTP Server Certificate Fail
018-570 HTTP Certificate Fail
018-571 Internal Error in Scan
018-572 Invalid Char in Context
018-573 Invalid Char in Server or Tree
018-574 Invalid Char in Volume
018-575 Invalid Char in Login
018-576 Invalid Char in Path
018-577 Invalid Char in File
018-578 Netware Server Not Found
018-579 Netware Server Disk Full
018-580 Netware Server Volume Not Exist
018-581 Netware Server Path Not Exist
018-582 Access Right Fail
018-583 Netware Server Disk Access Error
018-584 Netware Server Access Fail
018-585 Netware Error in Use
018-586 Netware Server Login Fail
018-587 File Duplication Fail
018-588 Scan Filing Policy Invalid
018-589 NEXTNAME.DAT Error
018-590 Same Name File Exists in Server
018-591 File Name Suffix Limit Over in Scan
018-592 Lock Folder Create Fail in Scan
018-593 Lock Folder Delete Fail in Scan
018-595 Duplicate ID is Detected
018-596 LDAP Protocol Error 596
018-701 LDAP Protocol Error 01
018-702 LDAP Protocol Error 02
018-703 LDAP Protocol Error 03
018-704 LDAP Protocol Error 04
018-705 LDAP Protocol Error 05
018-706 LDAP Protocol Error 06
018-707 LDAP Protocol Error 07
018-708 LDAP Protocol Error 08
018-710 LDAP Protocol Error 10
018-711 LDAP Protocol Error 11
018-712 LDAP Protocol Error 12
018-713 LDAP Protocol Error 13
018-714 LDAP Protocol Error 14
018-716 LDAP Protocol Error 16
018-717 LDAP Protocol Error 17
018-718 LDAP Protocol Error 18
018-719 LDAP Protocol Error 19
018-720 LDAP Protocol Error 20
018-721 LDAP Protocol Error 21
018-732 LDAP Protocol Error 32
018-733 LDAP Protocol Error 33
018-734 LDAP Protocol Error 34
018-735 LDAP Protocol Error 35
018-736 LDAP Protocol Error 36
018-748 LDAP Protocol Error 48
018-749 LDAP Protocol Error 49
018-750 LDAP Protocol Error 50
018-751 LDAP Protocol Error 51
018-752 LDAP Protocol Error 52
018-753 LDAP Protocol Error 53
018-754 LDAP Protocol Error 54
018-764 LDAP Protocol Error 64
018-765 LDAP Protocol Error 65
018-766 LDAP Protocol Error 66
018-767 LDAP Protocol Error 67
018-768 LDAP Protocol Error 68
018-769 LDAP Protocol Error 69
018-770 LDAP Protocol Error 70
018-771 LDAP Protocol Error 71
018-780 LDAP Protocol Error 80
018-781 LDAP Protocol Error 81
018-782 LDAP Protocol Error 82
018-783 LDAP Protocol Error 83
018-784 LDAP Protocol Error 84
018-785 LDAP Protocol Error 85
018-786 LDAP Protocol Error 86
018-787 LDAP Protocol Error 87
018-788 LDAP Protocol Error 88
018-789 LDAP Protocol Error 89
018-790 LDAP Protocol Error 90
018-791 LDAP Protocol Error 91
018-792 LDAP Protocol Error 92
018-793 LDAP Protocol Error 93
018-794 LDAP Protocol Error 94
018-795 LDAP Protocol Error 95
018-796 LDAP Protocol Error 96
018-797 LDAP Protocol Error 97
021-210 USB IC Card Reader Connection State Error
021-360 EP Accessory Fail
021-361 EP Accessory Kind Config Error
021-500 EPAccessoryJobExclusion
021-501 Illegal Server URL
021-502 Proxy Server Address Solution Error
021-503 Server Address Solution Error
021-504 Server Connection Error
021-505 SSL Session Error
021-506 Invalid SSL Certificate (EdgeServer)
021-507 Proxy Authentication Error
021-508 Communication Timeout
021-509 Invalid Communication Message
021-510 Inconsistency of Withdrawal Status (EP System) Message
021-511 Inconsistency of Installationl Status (EP System) Message
021-512 EP-SV Installation Conflict (EP system)
021-513 EP-DX Installation Conflict (EP system)
021-514 TRESS Installation Conflict (EP system)
021-515 Wrong M/C Type Code
021-516 Wrong Serial Number
021-517 Communication Failure (EP Center)
021-518 Internal Error (EdgeServer)
021-519 High Load Status Detected (EP Center)
021-520 CA Communication Error
021-521 CA Communication Timeout
021-522 Certificate Library Error
021-523 Internal Error
021-524 Inconsistency of Installation Status
021-525 Inconsistency of Withdrawal Status
021-526 Communication Library Error
021-527 Communication Library Error
021-528 Communication Setting Error
021-731 EP Accessory - Disabled Function
021-732 EP Accessory Error 732
021-733 EP Accessory Error 733
021-750 Used Parts Request Fail (EP-SV)
021-751 Maintenance Request Fail (EP-SV)
021-770 Used Parts Request Fail (EP-DX)
021-771 Maintenance Request Fail (EP-DX)
021-772 EPDX Install, Remove Error
021-941 EP - Scan Service Paused By Disable
021-942 EP - Scan Service Paused By Color Mode
021-943 EP - Print Service Paused By Disable
021-944 EP - Print Service Paused By Color Mode
021-945 EP - Service Paused By Disable
021-946 EP - Service Paused By Color Mode
021-947 Subtractive Accessory Disable (Scan)
021-948 Subtractive Accessory Disable (Print)
021-949 Subtractive Accessory Disable
024-340 RAP IOT-ESS Communication Failure 1. ESS PWB detected a communication failure between IOT and ESS.
024-341 RAP IOT-ESS Communication Failure 2. ESS PWB detected a communication failure between IOT and ESS.
024-342 RAP IOT-ESS Communication Failure 3. ESS PWB detected a communication failure between IOT and ESS.
024-343 RAP IOT-ESS Communication Failure 4. ESS PWB detected a communication failure between IOT and ESS.
024-345 RAP IOT-ESS Communication Failure 5. ESS PWB detected a communication failure between IOT and ESS.
024-346 RAP IOT-ESS Communication Failure 6. ESS PWB detected a communication failure between IOT and ESS.
024-347 RAP IOT-ESS Communication Failure 7. ESS PWB detected a communication failure between IOT and ESS.
024-348 RAP IOT-ESS Communication Failure 8. ESS PWB detected a communication failure between IOT and ESS.
024-349 RAP IOT-ESS Communication Failure 9. ESS PWB detected a communication failure between IOT and ESS.
024-350 RAP IOT-ESS Communication Failure 10. ESS PWB detected a communication failure between IOT and ESS.
024-351 RAP IOT-ESS Communication Failure 11. ESS PWB detected a communication failure between IOT and ESS.
024-352 RAP IOT-ESS Communication Failure 12. ESS PWB detected a communication failure between IOT and ESS.
024-353 RAP IOT-ESS Communication Failure 13. ESS PWB detected a communication failure between IOT and ESS.
024-354 RAP IOT-ESS Communication Failure 14. ESS PWB detected a communication failure between IOT and ESS.
024-355 RAP IOT-ESS Communication Failure 15. ESS PWB detected a communication failure between IOT and ESS.
024-356 RAP IOT-ESS Communication Failure 16. ESS PWB detected a communication failure between IOT and ESS.
024-357 RAP IOT-ESS Communication Failure 17. ESS PWB detected a communication failure between IOT and ESS.
024-358 RAP IOT-ESS Communication Failure 18. ESS PWB detected a communication failure between IOT and ESS.
024-359 RAP IOT-ESS Communication Failure 19. ESS PWB detected a communication failure between IOT and ESS.
024-360 RAP IOT-ESS Initialization Failure.
024-361 RAP Invalid IOT PaperSizeGroup Information.
024-362 RAP Page Sync Illegal Start. PageSync became active before writing reached the point where the output data filled the FIFO during IOT output.
024-363 RAP Page Sync Illegal Stop. PageSync became invalid before the specified size was output during IOT output.
024-364 RAP DMA Transfer Failure. The specified data was input but compression or expansion did not complete when compression or expansion was being performed.
024-365 RAP Overflow on the Loop Back Write.
024-366 RAP JBIG Library Other Failure.
024-367 RAP Decompress Other Failure. An incorrect line sync was detected during IOT output.
024-368 RAP PCI Error. A failure occurred during PCI access because the PCI bus was incompatible.
024-370 RAP Marker Code Detect Failure. The end code was not found in the compressed data when, during expansion, it was expanded to the specified size.
024-371 RAP IOT-ESS Communication Failure 21. ESS PWB detected a communication failure between IOT and ESS.
024-372 RAP IOT-ESS Communication Failure 22. ESS PWB detected a communication failure between IOT and ESS.
024-373 RAP IOT-ESS Communication Failure 23. ESS PWB detected a communication failure between IOT and ESS.
024-374 RAP Regi Con PLL Parameter Failure.
024-375 RAP IOT-ESS Communication Failure 24. ESS PWB detected a communication failure between IOT and ESS.
024-600 RAP Billing master counter repair.
024-601 RAP Billing backup counter #1 repair.
024-602 RAP Billing backup counter #2 repair.
024-603 RAP SWKey master counter repair.
024-604 RAP SWKey backup counter #1 repair.
024-605 RAP SWKey backup counter #2 repair.
024-606 RAP Production Number/Serial Number Failure.
024-700 RAP Job that is unprintable due to [System memory capacity shortage] or [HDD unmounted] is received.Job added with any of AnalogWaterMark/HighbridWaterMark/UUID is submitted to this M/C where the following both condition 1 and condition 2 are met:1.Any of SW option "Paper Security Kit", "Annotation Kit" and "Sakuragami Kit" is valid. Note that a case with two valid options as well as a case with 3 valid options are also included.2.HDD is not mounted on Controller board, or System memory capacity is not sufficient for valid SW option in the above condition 1 to operate.
024-742 RAP Printer job canceled due to Booklet sheets over the limit.Number of sheets for one set is over the limit for Booklet.
024-746 RAP Selected Paper Tray Parameter Mismatch. A function was specified (one of Paper Size, Paper Tray, Output Tray, and Duplex Printing) that is not compatible with the type of paper specified.
024-747 RAP Print Instruction Failure. Job is not executable or continuable with designated parameter combination (storage file size, paper size, paper tray, Duplex designation, output tray). This error occurs also when job is not continuable even when "Start" button is pressed after temporary stop due to parts failure caused during printing operation..
024-748 RAP Excessive number of digit in Bates Numbering. Max. number of digit (9 digits) or user-designated number of digit is exceeded while Bates Numbering is printed.
024-775 RAP Job canceled due to Booklet sheet over the limit. (Occurs without imposition.)Detected at start of Print. Number of sheets per set for Printer Print is over the limit for Booklet.
024-910 RAP Tray 1 Size Mismatch. When the paper length in Slow Scan direction is measured on the paper feed path, the size detected is different from the size detected by the Tray.
024-911 RAP Tray 2 Size Mismatch. When the paper length in Slow Scan direction is measured on the paper feed path, the size detected is different from the size detected by the Tray.
024-912 RAP Tray 3 Size Mismatch. When the paper length in Slow Scan direction is measured on the paper feed path, the size detected is different from the size detected by the Tray.
024-914 RAP Tray 6 Size Mismatch. When the paper length in Slow Scan direction is measured on the paper feed path, the detected size is different from the size detected by the HCF Tray.
024-915 RAP Tray 7 Size Mismatch. When the paper length in Slow Scan direction is measured on the paper feed path, the size detected is different from the size detected by the Tray.
024-916 RAP Stacker Tray Full (Mixed Size Set).
024-917 RAP Finisher Stacker Tray Set Over Count. The Stapled Set count exceeded 50 sets on the Stacker Tray during the Staple Set Eject operation.
024-920 RAP Face Down Tray1 Paper FULL
024-923 RAP Yellow Toner Cartridge Empty
024-924 RAP Magenta Toner Cartridge Empty
024-925 RAP Cyan Toner Cartridge Empty
024-926 RAP Puncher Waste Bin Missing
024-927 RAP Offset Catch Tray Full Stack
024-931 Staple Waste Container Full-Finisher
024-932 RAP Finisher Staple Waste Bin Not Set
024-934 RAP Paper type mismatch
024-935 RAP Tray 1 Paper Mismatch.
024-936 RAP Tray 2 Paper Mismatch.
024-937 RAP Tray 3 Paper Mismatch.
024-939 RAP Transparency type mismatch (No white border)
024-942 RAP Booklet Sheets Over Count. The number of sheets in a booklet is over the limit.
024-943 RAP Booklet Low Staple. There are few remaining staples. (This fault can also occur if the cartridge is removed.)
024-945 RAP Booklet Full Stack. The number of sets sent to the Booklet Tray without clearing the stack has reached the system data threshold.
024-946 RAP Tray 1 Not In Position. Tray 1 has not been inserted properly.
024-947 RAP Tray 2 Not In Position. Tray 2 has not been inserted.
024-948 RAP Tray 3 Not In Position. Tray 3 has not been inserted.
024-950 RAP There is no paper in Tray 1.
024-951 RAP There is no paper in Tray 2.
024-952 RAP There is no paper in Tray 3.
024-954 RAP There is no paper in Tray 5.
024-955 RAP There is no paper in Tray 6.
024-956 RAP Operation Error. Tray 7 Empty. No paper in Tray 7 is detected. NO Standard Tray 7 for this machine
024-957 RAP Interposer Empty. Add paper.
024-958 RAP Tray 5 Size Mismatch. The paper size loaded in the Tray and the paper size specified for printing are not the same size.
024-959 RAP Tray 1 Paper Size Mismatch. The paper in Tray 1 and the paper specified for printing are different.
024-960 RAP Tray 2 Paper Size Mismatch. The paper in Tray 2 and the paper specified for printing are different.
024-961 RAP Tray 3 Paper Size Mismatch. The paper in Tray 3 and the paper specified for printing are different.
024-965 RAP ATS/APS No Paper. The paper specified for printing has run out.
024-966 RAP ATS/APS No Destination Error. The paper specified for printing cannot be detected.
024-967 RAP Different Width Mix Paper Detect (Staple Job). A mix of different widths was detected when it was specified that stapling is only possible when all the widths are the same.
024-968 RAP Stapler/Punch Batting. Stapler and punch batting.
024-969 RAP Different Width Mix Punch. Paper of different widths was detected while printing in punch mode.
024-970 RAP Tray 6 (HCF) not In Position. Tray 6 has not been inserted.
024-971 RAP Tray 7 Not In Position. Tray 7 has not been inserted.
024-972 RAP Tray 6 Paper Size Mismatch. The paper in Tray 6 and the paper specified for printing are different.
024-973 RAP Tray 7 Paper Size Mismatch. The paper in Tray 7 and the paper specified for printing are different.
024-974 RAP Interposer Tray Size Mismatch. Designated paper size and Tray paper size are different in paper feed from Interposer.
024-975 RAP It was detected that the number of sheets for Booklet was exceeded when printing started. The number of sheets loaded exceeded the maximum number of sheets possible for Booklet.
024-976 RAP Finisher Staple Status incorrect. The staple home sensor's changing from off to on was not detected within 450 ms after the start of a forward rotation operation, and the staple head home sensor came on within 200 ms after the staple motor reverse rotation.
024-977 RAP Stapler Feed Ready Failure
024-978 RAP Booklet Stapler incorrect. The ready signal was still not ready at the specified time after the start of a booklet stapling operation.
024-979 RAP Stapler Near Empty. The stapler is nearly out of staples, or there was a problem in stapling (treated as the empty condition).
024-980 RAP Finisher Stacker Tray Full.
024-981 RAP Finisher Top Tray Full. The Top Tray Sensor was on for 10 consecutive seconds.
024-982 (A/P Finisher) RAP Stacker Lower Safety Warning. The Stacker Tray Lower Safety Switch came on.
024-983 RAP Booklet Tray Full.
024-984 RAP Booklet Low Staple F
024-985 RAP SMH Stop Check
024-987 RAP Envelope Folder Tray Full. When the specified number of paper sheets are output after Envelop Tray Near Full is detected.
024-988 RAP Envelop Folder Tray Set Fail. Envelop Tray Set SNR is monitored at 100msec interval, OFF is detected for successively 10 times.
024-989 RAP Booklet Low Staple R
024-990 RAP Puncher Waste Bin Full.
025-596 RAP Diag HDD Failure 1. NG came up during DC355 HDD failure prediction.
025-597 RAP Diag HDD Failure 2. An error occurred during DC355 HDD initialization.
026-700 LDAP Protocol MAX Error
026-701 Address Book Request Overflow
026-702 Address Book Directory Service Overflow
027-400 RAP Net Off Line
027-442 RAP Duplicat IP address. Device with the same IP address as IPv6 "Stateless Auto Setting Address1" of M/C exists in the network. Bit0 Duplicated address with autoConfInet6Address[0] of PFRID_IPV6_PROT_AUTO. When 027-442 to 027-447 occur at a time, the faults are displayed in ascending order of Link number.
027-443 RAP DNS renewal failure of dynamic. Device with the same IP address as IPv6 "Stateless Auto Setting Address2" of M/C exists in the network. Bit1 Duplicated address with autoConfInet6Address[0] of PFRID_IPV6_PROT_AUTO. When 027-442 to 027-447 occur at a time, the faults are displayed in ascending order of Link number.
027-444 RAP Duplicat IP address. Device with the same IP address as IPv6 "Stateless Auto Setting Address3" of M/C exists in the network. Bit2 Duplicated address with autoConfInet6Address[0] of PFRID_IPV6_PROT_AUTO. When 027-442 to 027-447 occur at a time, the faults are displayed in ascending order of Link number.
027-445 RAP Illegal IP address. IPv6 "Manual setting address"set to M/C is not correct. *Bit13 Address allocation error with inet6Address of PFRID_IPV6_PROT_MANUAL. When 027-442 to 027-447 occur at a time, the faults are displayed in ascending order of Link number.
027-446 RAP Duplicat IP address. Device with the same IP address as IPv6 "Manual setting address"of M/C exists in the network. *Bit14 Duplicated address with inet6Address of PFRID_IPV6_PROT_MANUAL. When 027-442 to 027-447 occur at a time, the faults are displayed in ascending order of Link number.
027-447 RAP Duplicat IP address. Device with the same IP address as IPv6 "Link local address" of M/C exists in the network. Bit15 Duplicated address with inkLocalAddress of PFRID_IPV6_PROT_AUTO. When 027-442 to 027-447 occur at a time, the faults are displayed in ascending order of Link number.
027-452 RAP Duplicate IP address. There are duplicate IP addresses.
027-500 RAP SMTP Server Address Resolution Failure. The SMTP server name was incorrect when sending a mail response.
027-501 RAP POP Server Address Resolution Failure. The POP server name was incorrect when using the POP3 protocol.
027-502 RAP POP Authentication Failure. Login to the POP server failed when using the POP3 protocol.
027-503 RAP POP server communication timeout. (POPERR_TIMEOUT).
027-504 RAP Response reception which is not expected from SMTP server.
027-513 RAP SMB Scan Client has no access right (Win9x).
027-514 RAP Host name resolution with SMB Scan fails. Resolution of SMB server host name or server name fails at DNS access in SMB transfer of scanner (Storage in PC).
027-515 RAP DNS server is not set with SMB Scan. DNS server is not set at DNS access in SMB transfer of scanner (Storage in PC).
027-516 RAP Problem in server connection with SMB Scan. SMB server cannot be found in SMB transfer of scanner (Storage in PC).
027-518 RAP Login name or a password error in SMB. Designated password is wrong in SMB transfer of scanner (Storage in PC).
027-519 RAP Scanning picture preservation place error in SMB.
027-520 RAP Acquisition of file/folder name with SMB Scan server fails.
027-521 RAP Suffix of SMB Scan file name/folder name exceeds the limit value..
027-522 RAP SMB Scan file creation failure. Scan image file creation in SMB server fails in SMB transfer of scanner (Storage in PC).
027-523 RAP SMB Scan lock folder creation failure. Lock folder creation in SMB server fails in SMB transfer of scanner (Storage in PC). Designated lock folder already exists.
027-524 RAP SMB Scan folder creation failure. Folder creation in SMB server fails in SMB transfer of scanner (Storage in PC). Designated folder already exists.
027-525 RAP SMB Scan file deletion in SMB Scan server fails.
027-526 RAP Lock folder deletion in SMB Scan server fails.
027-527 RAP Folder deletion in SMB Scan server fails.
027-528 RAP No available space in storage destination of SMB Scan data server.
027-529 RAP Unexpected error response is received from SMB server or unexpected error occurs in M/C, in SMB transfer of scanner (Storage in PC).
027-530 RAP Job Cancel (No storage)" is selected as processing at SMB Scan file name duplication occurrence. File cannot be stored since processing to be conducted at the occurrence of file name duplication is set to "Job Cancel (Not to store)" in SMB transfer of scanner (Storage in PC).
027-531 RAP Illegal SMB Scan filing policy (When "Add" is selected).
027-532 RAP File access error in SMB transfer of scanner (PC storage). Error occurs when NEXTNAME.DAT file is accessed in SMB transfer of scanner (Storage in PC).
027-533 RAP Internal error occurs in SMB Scan.
027-543 RAP SMB server (NetBIOS) name designation is incorrect. SMBCL_NG_INV_HOST Host name designation is incorrect.
027-547 RAP SMB Protocol Error (4-007). Designation of scan domain name is illegal. Domain name designated is illegal" is detected by Controller software (SMB Library).
027-548 RAP SMB Protocol Error (4-008) Designation of scan user name is illegal. "User name designated is illegal" detected by Controller software (SMB Library).
027-549 RAP SMB Protocol error (4-009). Password designation is illegal.
027-564 RAP SMB Protocol error 4-024. Host is not found.
027-565 RAP SMB Protocol error (4-025). Cannot connect.
027-566 RAP SMB Protocol error (4-026). Library is not initialized.
027-569 RAP SMB(TCP/IP) is not activated. SMBCL_NG_NOT_INIT occurring with SMB Scanner Library is not initialized.
027-572 RAP SMB Protocol error (4-032). Illegal parameter.
027-573 RAP SMB Protocol error (4-033). Illegal character code.
027-574 RAP SMB Protocol error (4-034). Illegal data size.
027-576 RAP SMB Protocol error (4-036). Illegal domain data size.
027-578 RAP SMB Protocol error (4-038). Communication time out.
027-579 RAP SMB Protocol error (4-038). Communication time out.
027-584 RAP SMB Protocol error (4-044). SMBCL_NG_INV_SECMODE Authentication Server is in operation in shared Security mode.
027-585 RAP SMB Protocol error (4-045)Scan login disabled time. “SMB Authentication/SMB Scanner case”. "Login disabled time" detected by M/C Controller software (SMB Library).
027-586 RAP SMB Protocol error (4-046)Password is expired. “SMB Authentication/SMB Scanner case”. "Password expired" detected by M/C Controller (SMB Library).
027-587 RAP SMB Protocol error (4-047) Need to change password. “SMB Authentication/SMB Scanner case”. "Need to change password" detected by M/C Controller (SMB Library).
027-588 RAP SMB Protocol error (4-048) User is invalid. “SMB Authentication/SMB Scanner case”. User is invalid.
027-589 RAP SMBProtocol Error (4-049) Lock out. “SMB Authentication/SMB Scanner case”. User is locked out.
027-590 RAP SMBProtocol Error (4-050) User is expired. “SMB Authentication/SMB Scanner case”. User is expired.
027-591 RAP SMBProtocol Error (4-051) User is limited. "Without password" is not permitted.
027-599 RAP SMB/LDAP Protocol error (Other code). SMB Library internal error other than 27-547 through 27-579 . Protocol type delivered to Coml_Fault_GetNETCeCode( ) is unexpected. FTP/HTTP/Undefined type is designated (DMP6-1)
027-600 RAP ExtPrint Check Mode Error. Controller detects error in external CDI H/W CheckMode.
027-700 RAP Media Failure. There was a media failure.
027-701 RAP Media Not Found. Media was not found.
027-702 RAP Certificate for destination does not exist (Before server is connected). When SMIME mail is sent (SMLNG_KEY_NOTHING).
027-703 RAP Certificate for destination is expired (Before server is connected). When SMIME mail is sent (VKCMERR_CERT_EXPIRED).
027-704 RAP Certificate for destination is expired (Before server is connected). When SMIME mail is sent (SMLNG_KEY_UNTRUST).
027-705 RAP Certificate for destination is found in discarding list (Before server is connected). When SMIME mail is sent (SMLNG_KEY_UNTRUST).
027-706 RAP Device certificate does not exist (before server connection). Certificate is not found when SMIME mail is sent.
027-707 RAP Device certificate is expired (before server connection). Expired (No longer valid) certificate is detected when SMIME mail is sent.
027-708 RAP Device certificate is untrusted (before server connection). Invalid certificate is detected when SMIME mail is sent.
027-709 RAP Device certificate is found in discarding list (before server connection). Revoked certificate is detected when SMIME mail is sent (Registered in CRL)
027-710 RAP S/MIME mail was disabled
027-711 RAP S/MIME mail sender certificate not found
027-712 RAP S/MIME mail sender certificate not valid
027-713 RAP S/MIME mail was altered

[dastin]

часть третья

027-714 RAP S/MIME mail sender impersonation
027-715 RAP S/MIME mail certificate not supported
027-716 RAP No-Signed mail receipt was rejected
027-720 RAP Ext Srv. Host Not Found. A server specified for a remote application was not found, or DNS resolution was not possible.
027-721 RAP Ext Srv. Not Found. An attempt was made to run a remote application but the response that the cooperating application was not found came from the directly reached host.
027-722 RAP Ext Srv. Timeout Failure. An attempt was made to run a remote application but it failed due to timeout.
027-723 RAP Ext Srv. Authentication Failure. An attempt was made to run a remote application but it failed during authentication.
027-724 RAP Ext Srv. Access Failure. An attempt to run a remote application failed. (This covers all cases that failure for a reason other than that the service was not found, timeout, or an authentication failure.)
027-725 RAP Ext Srv. Operation Failure. The job processing at the site of the remote application failed.
027-726 RAP Ext Srv. Unknown State. The job status at the site of the remote application is unknown.
027-727 RAP Ext Srv. Req Invalid Params. A parameter used by a remote application was incorrect.
027-728 RAP Ext Srv. Required File Exceeded
027-730 RAP Mail division error (Before server is connected). Mail division problem occurs in system linkage.
027-731 RAP Job Template server Accept Limit Error. Concurrent activation of CWSS NetWareJob and NetWare polling.
027-732 RAP Job Template server Access Error. Job Template server capacity is insufficient or failure occurs with server disk.
027-733 RAP Job Template server SSL Error. SSL setting of Job Template server is not valid.
027-734 RAP Job Template server Certificate Error. Server certificate is not valid.
027-735 RAP Device SSL Config Error. SSL setting of the device is invalid for transfer request using SSL.
027-736 RAP Device Certificate Error. Server certificate authentication of the device is invalid for server certificate authentication request.
027-737 RAP Template Server Read ERR. An error came from the job template pool server when reading data.
027-739 RAP Invalid Template Server Path. The specified job template pool server was not found.
027-740 RAP Template Server Login ERR. It was not possible to log into the job template pool server.
027-741 RAP Template Server Connect Failure. It was not possible to connect to the job template pool server.
027-742 RAP HD File System Full. A job template could not be stored because of insufficient HDD area.
027-743 RAP Template Server Install ERR. The installation of the job template pool server was not correct.
027-744 RAP Template Server ADD ERR. There was a problem with the domain name of the job template pool server.
027-745 RAP Template Server ADD ERR. The address of the DNS server is not installed in the M/C.
027-746 RAP Job template pool server protocol startup error. Protocol port designated with job template pool server setting is not activated.
027-750 RAP IFAX transfer is requested while it is inhibited. While Ifax transfer and e-mail of Ifax document are inhibited, e-mail/Ifax transfer are requested. Printing of scanned/printer document is requested in Interrupt.
027-751 RAP Job Template Analysis Error. An error was detected during analysis of the specified document.
027-752 RAP Must User Not Input. It was specified that a job be started while a required user input had not been input.
027-753 RAP Job Flow Service Request Disabled. The specified document service is invalid.
027-754 RAP File signature setting mismatch of job flow indication.
027-760 RAP XJT Command Failure. A command from an XDOD client was incorrect.
027-770 RAP PDL Error When a job contains a PDL error.When a job size exceeds 4GB.
027-771 RAP DFE Disk Full
027-772 RAP SMTP server rejects HELO command (After server is connected). (SMTPERR_HELO_FAIL)
027-773 RAP Timeout in communication with SMTP server (After server is connected). (SMTPERR_TIMEOUT).
027-774 RAP Illegal character is designated for destination address (After server is connected). (SMTPERR_INVALID_CHARACTER).
027-775 RAP Error due to too many destination mail addresses (After server is connected). (SMTPERR_TOO_MANY_RECIPIENTS)
027-776 RAP SMTP server rejects EHLO command (After server is connected). (SMTPERR_EHLO_FAIL)
027-777 RAP SMTP server does not support SMTP-AUTH (After server is connected). (SMTPERR_AUTH_NONSUPPORT)
027-778 RAP Mode designated with SMTP-AUTH is not found (After server is connected). (SMTPERR_AUTH_METHOD)
027-779 RAP Authentication fails with SMTP-AUTH (After server is connected). (SMTPERR_AUTH_FAILED)
027-796 RAP Email Not Printed. Mail was discarded because the mail was received with no attached document and it was specified that only the documents attached to received mail should be printed.
027-797 RAP Invalid Output Destination. The output destination for received mail was incorrect.
034-211 Fax Option Slot1 Board failure.
034-212 Fax Option Slot2 Board failure.
034-500 Illegal data is included in dial data.
034-501 Designated channel is not available. Processing is requested for unimplemented channel.
034-505 Fax work memory overflow during communication. Fax Card Memory Full
034-506 Remote M/C has not remote sort copy ability.
034-507 Password check error. Mailbox number error. Document for polling reservation not found.
034-508 Communication is canceled by command rejection signal transmission.
034-509 Communication is canceled by receiving invalid procedure signal.
034-510 Communication is canceled by receiving command rejection signal.
034-511 Remote M/C has not file transfer ability.
034-512 Infinite loop is detected in remote Relay Broadcast.
034-513 Illegal command is received from remote M/C in remote maintenance.
034-514 Remote maintenance is requested from remote M/C but is not supported.
034-515 DIS is received from calling terminal. DCS is received though receive ability is not provided. Illegal command is received.
034-519 The number of destination exceeds a specified limit value. (The number of full-dial request exceeds 200 terminals).
034-520 The number of service exceeds a specified limit value.
034-521 Fax Card I/F error. Service designated with SI does not exist (This error may not be sent back due to cross sequence fix).
034-522 No line is available for manual communication.
034-523 Fax operation is inhibited. Send service cannot be accepted due to fax operation-inhibited status of remote M/C in execution of EP-TRESS system or Diag service.
034-527 Dial Control Error
034-528 Manual communication request is detected during dialing of M/C.
034-529 Loaded paper does not match original size to be printed in Confirmation Print/Receive Print.
034-530 DTMF I/F timeout. Correct operation is not conducted within a specified time.
034-531 DTMF I/F timeout. Correct operation is not conducted within a specified time.
034-550 Error is detected during data write in FaxCard-ROM (with DLD method). Error is detected during FaxCard-ROM write. ROM content is deleted and the operation is not conducted properly.
034-700 GCP lock (Date task noRTC ACK). G3 Dicep not changed into idle status, causing timeout. CODEC hang-up.
034-701 Software reset.
034-702 Calling from FaxCard is disabled because of no dialing data. The relevant speed dial may be deleted after job registration.
034-703 D channel link disconnection (DL-link disconnection display received). Link disconnection from the network.
034-704 D channel link disconnection (DL-link disconnection display received). TEI allocation error. DISC command received with multi-frame setting in timer recovery status. UA response received with TEI allocation and multi-frame setting in timer recovery status.
034-705 D channel link disconnection (DL-link disconnection display received). Layer1 stop (with power supply).
034-706 D channel link disconnection (DL-link disconnection display received). Layer1 stop without power supply (socket coming off).
034-707 FRMR received.
034-708 Error frame received N (R )
034-709 Error frame received
034-710 Error frame received
034-711 Link establishment wait timeout. Link setting fails. T.200 Timeout occurs N.200 times in the wait for link setting/link re-setting.
034-712 Primitive send error (Internal Interrupt error).
034-713 Calling acceptance wait timeout (T303 2nd time).
034-714 Disconnection wait timeout (T305).
034-715 Disconnection completion wait timeout (T308 2nd time).
034-716 Call response wait timeout(T313 ).
034-717 Communication restart wait timeout(T318).
034-718 Disconnection recovery with received status display. Normal disconnection.
034-719 No free channel. Normal disconnection. No available channel.
034-720 60-sec guard timer timeout
034-721 Upper layer primitive format error, Content Error.
034-722 Timeout during suspension
034-723 No assigned timer.
034-724 Error sequence(Local terminal ID setting inconsistency).
034-725 L3 Task internal error.
034-726 HD81501 I/F Buffer busy.
034-727 No response to 1300Hz incoming call from Task for 3 sec or more
034-728 Unable to call Remote M/C due to wrong dial number.
034-729 Line disconnection during in-channel PB transmission.
034-730 Collision of incoming/outgoing call. The problem occurs when internal/external kit is not correctly mounted.
034-731 Fax Setup is disconnected from the network.
034-732 Fax network disconnection monitoring timeout.
034-733 Error sequence. Calling status inconsistency is detected. Sequence Error, Message Incompatible with State of Call
034-734 HI Task internal error.
034-735 Connection completion received with only D channel service.
034-736 Error message from the network.
034-737 Incoming call response error.
034-738 Layer1 activation failure(Activation timer timeout).
034-739 Layer1 out of synchronization (Synchronization monitoring timer timeout).
034-740 Frame send failure (Frame send completion monitoring timer timeout).
034-741 Frame send disabled (Frame send retry over).
034-742 Frame send underrun is detected.
034-743 Frame send DMA error end.
034-744 Unacceptable Channel.
034-745 Call request for already-set channel.
034-746 No available line channel. No circuit/channel available.
034-747 Switching equipment congestion.
034-748 Requested channel is not available.
034-749 Other (Network congestion class).
034-750 Network failure.
034-751 Network failure.
034-752 Remote terminal busy.
034-753 No response from remote user. Destination not responding.
034-754 No response from remote user during calling. No answer to user alert.
034-755 Remote terminal rejects communication. Destination rejecting call.
034-756 Remote terminal is in failure. Destination out of order.
034-757 Other (Normal - Semi-normal class).
034-758 Illegal Destination Fax Dial Number. Unassigned or invalid number.
034-759 No relay network route. No route to specified transit network.
034-760 No route to remote terminal. No Line To Destination.
034-761 Invalid number format(Incomplete number). Invalid number format (Incomplete number).
034-762 Facility rejection.
034-763 Communication capability not authorized.
034-764 Currently-unavailable communication capability. Com. Capability not configured.
034-765 Verify telephone number and request remote terminal to provide another terminal if telephone number is normal. ISDN line is not connected. Verify ISDN line connected and if not connected, connect the ISDN line.
034-766 Undefined transfer capability designated. Communication capability not implemented.
034-766 Undefined transfer capability designated. Communication capability not implemented.
034-767 Undefined channel type designated. Selected mode not implemented.
034-768 Only limited digital information is available. Restricted Digital Info. Only.
034-769 Retry sending info. Verify telephone number and request remote terminal to provide another terminal if telephone number is normal. ISDN line is not connected. Verify ISDN line connected and if not connected, connect the ISDN line.
034-770 Response to status inquiry.
034-771 Access information discarded.
034-772 Other (Mutual connection class). Unspecified inter-working connection error.
034-773 Invalid calling number ( Dial No.) used.
034-774 Invalid channel number used. Invalid Line Specified.
034-775 Other (Invalid message class). Unspecified (Invalid message).
034-776 Mandatory information shortage. Mandatory information element is missing.
034-777 Message type undefined.
034-778 Illegal Message or Type. Inconsistency of call status and message, or message type undefined.
034-779 No information element or undefined.
034-780 Invalid information element contents.
034-781 Call Status, Message Mismatch. Inconsistency of call status and message.
034-782 Recovery with timer timeout. Error cleared due to timeout.
034-783 Other Errors (Operation, etc). Unspecified (Protocol error).
034-784 Remote terminal number change.
034-785 Terminal attribute inconsistency. Incompatible destination.
034-786 Designation of disconnection call identification number not in use. Call identity not in use.
034-787 Designation of disconnection call identification number currently in use. Call identity in use.
034-788 Display of other error causes.
034-789 CG conversion timeout (G4) Presentation receives illegal event.
034-790 Channel0 Internal line is not connected. Line 0 (Extension) not connected.
034-791 Channel1 External line is not connected.
034-792 Channel2 is not connected.
034-793 Channel3 is not connected.
034-794 Channel4 is not connected.
034-795 Channel5 is not connected.
034-796 Dial Error (illegal Fax No. 2). Illegal data exists in dial data.
034-797 Job error communication option parameter has error. Communication option parameter error.
034-798 Job error communication data parameter has error. Communication data parameter error.
034-799 Auto Dial is activated but no dial data is found.
035-550 FaxG3-ROM (With DLD Method) Error
035-700 G3 Modem Error
035-701 T1 Transmission Timeout
035-702 Destination Receive Rejected
035-703 DCN Receive at Phase B Send
035-704 Destination Polling Error
035-705 DCS/NSS Resend Exceeded
035-706 Fallback Error
035-707 Illegal Password/Receive Banned
035-708 Post-Message Resend Exceeded
035-709 RTN Receive
035-710 PIN Receive
035-711 DCN Receive at Phase D
035-712 Wrong Password
035-713 T2 Timeout After Sending FTT
035-714 DCN Received After NSC/DTC
035-715 Illegal Password-Polling Error
035-716 No Post Message
035-717 No Post Message
035-718 Receive T1 Timeout
035-719 Busy Tone Detected at Phase-B
035-720 Busy Tone Detected at Phase-B
035-721 DCN Received at Phase B
035-722 Wrong Frame Length of 300bps
035-723 No CD After Receiving Flag
035-724 DCN Receive After Sending FTT
035-725 Remote Has No Mailbox/Relay
035-726 PhaseC Cannot Receive
035-727 PhaseC Error
035-728 PHASE-C EOL Error
035-729 Carrier Down Detected
035-730 No CS with Phase-C High Speed
035-731 Fax V.8 Error
035-732 Fax V.34 PCH CD Off
035-733 No V.34 C/P-CH CS
035-734 Polling ERR at Remote Step V8
035-735 No Doc. in Polling Box Step V8
035-736 No Reply DCN after Sending CTC
035-737 No Reply DCN after Sending EOR
035-738 No Reply DCN after Sending RR
035-739 Fax T5 Timeout
035-740 Sending Stopped after EOR Send
035-741 ECM Phase C Flag Timeout
035-742 EOR Send or Receive
035-743 Remote Cannot Receive SUB.
035-744 Remote Cannot Receive Password
035-745 PTX Has No SEP Capability
035-746 Busy-Cannot Detect Dial Tone
035-747 Abort While Dialing
035-748 Abort During Transmission
035-749 Abort During Transmission
035-750 Power Off During Transmission
035-751 Doc. Send Operation Canceled
035-752 No. of Job Restriction Error
035-753 Fax Memory Full
035-754 File Management Memory Full
035-755 File Add Page Error
035-756 Cannot Add Page
035-757 No Receive Page
035-758 No Specified File or Page
035-759 No Specified Job
035-760 File Processing Error
035-761 File Unspecified Error
035-762 File Unspecified Error
036-500 RDRP Parameter Error
036-501 RDPBP Parameter Error
036-502 RDPBN Parameter Error
036-503 RDCLP Parameter Error
036-504 RDGR Parameter Error
036-505 Undefined Response
036-506 Negotiation Disabled
036-507 RDPBP Receive at Full Capacity
036-508 RDPBN Receive Terminal Error
036-509 RDPBN Receive Others
036-510 RDPBN Receive
036-511 Procedure Error 1551
036-512 CDS Parameter Error
036-513 CDC Parameter Error
036-514 CDE Parameter Error
036-515 CDD Parameter Error
036-516 CDR Parameter Error
036-517 CDPB Parameter Error
036-518 CDCL Parameter Error
036-519 Undefined command
036-520 Not Negotiable CDS Receive
036-521 Not Negotiable CDC Receive
036-522 CDD Receive Terminal Error
036-523 CDD Receive Unspecified Error
036-524 CDD Receive Terminal Error
036-525 CDR Receive Unspecified Error
036-526 CDUI Parameter Error
036-527 CDUI Parameter Error
036-528 CDUI Parameter Error
036-529 CDUI Parameter Error
036-530 CDS Receive-Illegal Document
036-531 DMA Channel1 Error
036-532 DMA Channel2 Error
036-533 Cannot Convert Resources
036-534 Decode Error in Data Convert
036-535 White Line Transfer Error (Compress)
036-536 White Line Transfer Error (Decomp)
036-537 No RTC During Data Convert
036-538 Document Descriptor Analysis Error
036-539 Page Descriptor Analysis Error
036-540 Text Unit Analysis Error
036-541 Page Boundary Without TU
036-542 Relay Broadcast Error in G4
036-550 FaxG3-ROM (With DLD Method) Error
036-700 G4 Communication Error
036-701 Receive Status Variable N(R) Error
036-702 Info Frame Size Exceeded (NI)
036-703 Monitor/Unnumbered Frame Error
036-704 Undefined Command/Response
036-705 N2 Timeout of Receive Timer
036-706 SABM Wait Timeout in G4
036-707 UA Wait Timeout in G4
036-708 Cannot Establish Link in G4
036-709 Forced Link End
036-710 FRMR Receive (Z=1)
036-711 FRMR Rreceived (Y=1)
036-712 FRMR Received (Z=1) W=1
036-713 FRMR Receive (W=1)
036-714 Global Address Receive
036-715 Line Open Timeout in G4
036-716 Line Open Timeout in G4
036-717 Abnormal LSI Operation
036-718 Disconnection Notice Timeout
036-719 C Line On But I Line Off
036-720 C Line Off But I Line On
036-721 I Line Off During Transmission
036-722 Call Cut During Flag Detect
036-723 Call Cut While Awaiting UA
036-724 Call Cut While Awaiting SABM
036-725 Disc Received Before Session
036-726 Illegal Header Received
036-727 Illegal Parameter of CC Packet
036-728 Illegal Parameter of CN Packet
036-729 Illegal Parameter of DT Packet
036-730 Illegal Parameter of RI Packet
036-731 Illegal Parameter of IT Packet
036-732 Illegal Parameter of CI Packet
036-733 Illegal Parameter of CF Packet
036-734 Undefined Packet is Received
036-735 CC Wait Timeout
036-736 CF Wait Timeout
036-737 CI Received Before G4 Session
036-738 DT Packet P(S), P(R) Error
036-739 RR/RNR Packet P(S) Error
036-740 Busy Timeout
036-741 SI Received in Transmission
036-742 SF Received in Transmission
036-743 DT Packet D Bit Error
036-744 G4 Wait for Reply Timeout
036-745 G4 CN Wait Timeout
036-746 G4 Disconnection Notice Timeout
036-747 Fast Select Response Received
036-748 Receive Remote Charge Request
036-749 LCGN Error
036-750 Procedure Error 1301
036-751 Illegal TCA Parameter
036-752 TCR Parameter Error
036-753 TCC Parameter Error
036-754 Illegal TBR Parameter
036-755 Illegal TDT Parameter
036-756 Undefined Ttransport Block Received
036-757 TCA Wait Timeout
036-758 TCR Wait Timeout
036-759 TCC Wait Timeout
036-760 TBR Wait Timeout
036-761 TDT Block Size Error
036-762 Disconnection Notice Timeout
036-763 Illegal Procedure 1401
036-764 Illegal CSS Parameter
036-765 Illegal CSE Parameter
036-766 Illegal CSA Parameter
036-767 Illegal CSUI Parameter
036-768 Illegal CSCC Parameter
036-769 Illegal RSSP Parameter
036-770 Illegal RSSN Parameter
036-771 Illegal RSEP Parameter
036-772 Illegal RSAP Parameter
036-773 Illegal RSUI Parameter
036-774 Illegal RSCCP Parameter
036-775 Undefined Command/Response
036-776 RSSN Receive
036-777 G4 Line Disconnect Notice Timeout
036-778 CSA Received (Wrong Terminal)
036-779 CSA Received (Others)
036-780 CSS Wait Timeout
036-781 RSSP Wait Timeout
036-782 RSAP Wait Timeout
036-783 RSEP Wait Timeout
036-784 RSCCP Wait Timeout
036-785 CSUI/RSUI Wait Timeout
036-786 RSSN Received (Illegal Password)
036-787 Illegal Password-Polling Error for Remote
036-788 Poll Send Error at Remote
036-789 No Password for RSSP Receive
036-790 Polling Rejected by Remote
036-791 Set Password-RSSP Received
036-792 CSE Received after RSSP Send
036-793 Select Communication Error
036-794 Line Ccut During ISDN Mode
036-795 Canceled by Remote Station
036-796 Sent Without Multiple Sets
036-797 Illegal Procedure 1501
036-798 Illegal RDEP Parameter
036-799 Illegal RDDP Parameter
GBC® AdvancedPunch™ Fault Codes
41-311 Laser Diode 24V Fuse Fail
41-312 ADC 24V Fuse Fail
41-324 PH F1 Fuse Fail
41-325 PH F2 Fuse Fail
41-326 PH F3 Fuse Fail
41-327 PH F4 Fuse Fail
41-328 PH F5 Fuse Fail
41-329 PH F6 Fuse Fail
41-330 PH F7 Fuse Fail
41-331 PH F8 Fuse Fail
41-332 PH F9 Fuse Fail
41-333 PH F10 Fuse Fail
41-344 IOT F1 Fuse Fail
41-345 IOT F2 Fuse Fail
41-346 IOT F3 Fuse Fail
041-500 RAP Error is detected in the processing of data write in IOT-ROM.(with DLD method). Not required as Downloader Fail cannot be displayed on PSW
041-501 RAP Error is detected in the processing of data write in IOT-NV memory -ROM.(with DLD method). Not required as Downloader Fail cannot be displayed on PSW.
LED (On PWBs) Status Information RAP
042-313 RAP Rear Cooling Fan Failure. Hi level exceeds the specified value while Rear Fan Fail signal is monitored for 12sec, 2sec after the start of Rear Fan operation.
042-320 RAP Yellow Drum Motor Drive Failure. Fail is defined when Drum Motor Y Fail signal is detected 5 times or more while being monitored every 0.1[s] interval from the start of Drum Motor Y operation.
042-321 RAP Magenta Drum Motor Drive Failure. Fail is defined when Drum Motor M Fail signal is detected 5 times or more while being monitored every 0.1[s] interval from the start of Drum Motor M operation.
042-322 RAP Cyan Drum Motor Drive Failure. Fail is defined when Drum Motor C Fail signal is detected 5 times or more while being monitored every 0.1[s] interval from the start of Drum Motor C operation.
042-323 RAP Black Drum Motor Drive Failure. Fail is defined when Drum Motor K Fail signal is detected 5 times or more while being monitored every 0.1[s] interval from the start of Drum Motor K operation.
042-324 RAP IBT Drive Motor Failure. Failure is defined when IBT Drive Motor Fail signal is detected 5 times or more while being monitored every 0.1[s] interval from the start of IBT Drive Motor operatin.
042-325 RAP Main Motor Failure. Fail is defined when Main Motor Fail signal is detected 5 times or more while being monitored every 0.1[s] interval from the start of Main Motor operaton.
042-326 RAP Belt at Home Position Too Long. Belt Home Position Sensor cannot be detected for a certain time from the start of IBT Drive Motor.
042-327 RAP Belt Position Failure. Belt position adjustment failure. The number of times in correction (adjustment) range is specified in NVM. Detected when Belt position exceeds the specified range.
042-328 RAP Belt Edge Sensor Failure. Detected when Edge Sensor reading (read value) does not change during one turn of Belt.
042-330 RAP Fuser Exhaust Fan Failure
042-331 RAP Blower Motor Fan Failure
042-600 RAP Belt Walk Failure. Detected when the number of times that Belt Walk value over a certain value is detected exceeds the detection threshold between Y and K engin during one turn of Belt.
042-601 RAP Belt Edge Learn Failure
042-602 RAP Belt Edge Check Failure
042-603 RAP Suction/Ozone Filter Life End Failure
045-310 RAP Image Ready NG. An internal processing error occurred in the ESS PWB.
045-311 RAP Controller Comm Failure. Communication was not possible between the ESS and the MCU.
045-312 RAP IOT Drive Serial I/F Error
045-314 RAP This fault is displayed because a time-out occurred while waiting for an expected signal that did not happen. This is a fail-safe function to prevent the machine from a run-away condition.
045-315 RAP Video Line M Fail. Non-lit Beam occurrence due to M VideoLine failure between VECKY and LDD is detected.
045-316 RAP Video Line K Fail. Non-lit Beam occurrence due to K VideoLine failure between VECKY and LDD is detected.
045-360 RAP CONTIF Error Y Fail. Vecky CONITIF setting error Y.
045-361 RAP CONTIF Error M Fail. Vecky CONITIF setting error M.
045-362 RAP CONTIF Error C Fail. Vecky CONITIF setting error C.
045-363 RAP CONTIF Error K Fail. Vecky CONITIF setting error K.
045-364 RAP IRECT Error Y Fail. IRECT Memory UnderRUN error or IRECT Common error (Y).
045-365 RAP IRECT Error M Fail. IRECT Memory UnderRUN error or IRECT Common error (M).
045-366 RAP IRECT Error C Fail. IRECT Memory UnderRUN error or IRECT Common error (C).
045-367 RAP IRECT Error K Fail. IRECT Memory UnderRUN error or IRECT Common error (K).
047-210 RAP OCT Offset Failure
047-310 RAP Output Comm Fail. IOT-Output comunication failure.
047-320 RAP All Out Tray Broken Fail. Paper cannot be output to any output device connected.
061-310 RAP Video ASIC 1 Fail. Y/M Video ASIC failure
061-311 RAP Video ASIC 2 Fail. C/K Video ASIC failure.
061-313 RAP SOS Long Failure Magenta. The interval between SOS signals was longer than the specified value.
061-315 RAP SOS Long Failure Black. The interval between SOS signals was longer than the specified value.
061-317 RAP SOS Short Failure Magenta. The interval between SOS signals was shorter than the specified value.
061-319 RAP SOS Short Failure Black. The interval between SOS signals was shorter than the specified value.
061-320 RAP Polygon Motor 1 Failure. Y/M Polygon Motor failure.
061-321 RAP Polygon Motor 2 Fail. C/K Polygon Motor failure.
061-323 RAP No SOS Failure Magenta. The SOS signal was not detected.
061-324 RAP No SOS Failure Cyan. The SOS signal was not detected.
061-325 RAP No SOS Failure Black. The SOS signal was not detected.
061-326 RAP ROS Connect Failure Yellow. The connection between the ROS LD and the MCU PWB failed.
061-327 RAP ROS Connect Failure Magenta. The connection between the ROS LD and the MCU PWB failed.
061-328 RAP ROS Connect Failure Cyan. The connection between the ROS LD and the MCU PWB failed.
061-329 RAP ROS Connect Failure Black. The connection between the ROS LD and the MCU PWB failed.
061-334 RAP ROS Yellow/Magenta VDD Failure. Y/M Polygon Motor Off, but ROS Y/M board is powered ON.
061-335 RAP ROS Black/Cyan VDD Failure. C/K Polygon Motor is Off, but ROS C/K board is powered ON.
061-336 RAP ROS Yellow/Magenta VDD Down Failure. ROS Y/M board is not powered ON while Laser lights.
061-337 RAP ROS Black/Cyan VDD Down Failure. ROS C/K board is not powered ON while Laser lights.
061-338 RAP SOS Stop Magenta Failure
061-339 RAP SOS Stop Black Failure
061-340 RAP ROS LD Failure Black. At least three channels (NVM 749-105) of the 32 channels had detected LD degradation when the LD alarm was generated.
061-341 RAP ROS LD Failure Yellow. At least three channels (NVM 749-105) of the 32 channels had detected LD degradation when the LD alarm was generated.
061-342 RAP ROS LD Failure Magenta. At least three channels (NVM 749-105) of the 32 channels had detected LD degradation when the LD alarm was generated.
061-343 RAP ROS LD Failure Cyan. At least three channels (NVM 749-105) of the 32 channels had detected LD degradation when the LD alarm was generated.
061-380 RAP ROS Data Failure Yellow. Serial data communication is not possible between the MCU PWB and ROS (hidden failure).
061-381 RAP ROS Data Failure Magenta. Serial data communication is not possible between the MCU PWB and ROS (hidden failure).
061-382 RAP ROS Data Failure Cyan. Serial data communication is not possible between the MCU PWB and ROS (hidden failure).
061-383 RAP ROS Data Failure Black. Serial data communication is not possible between the MCU PWB and ROS (hidden failure).
061-604 RAP LD Alarm Yellow. Y LD deterioration.
061-605 RAP LD Alarm Magenta. M LD deterioration.
061-606 RAP LD Alarm Cyan. C LD deterioration.
061-607 RAP LD Alarm Black. K LD deterioration.
062-210 RAP IISS Hot Line Failure. It was detected that the hot line signal was disconnected.
062-211 RAP IIT/IPS EEPROM Failure (IPS). A write failure to EEPROM or a communication failure with EEPROM (retry) occurred.
062-220 RAP IPS-EXT Connection Failure.
062-277 RAP IIT/IPS-DADF Communication Failure. Communication between the IIT/IPW PWB and the DADF PWB was not possible.
062-300 RAP Platen Interlock Open. The platen interlock is open.
062-310 RAP IIT/IPS-ESS Communication Failure. Communication between the IIT/IPS PWB and the ESS PWB is not possible.
062-311RAP IIT Software Logic Failure. A software problem was detected with the IIT/IPS PWB.
062-321 RAP IPS-YATA Connection Failure
062-322 RAP EXT-YATA Connection Failure
062-323 RAP YATA PWBA Failure
062-345 RAP IIT/IPS EEPROM Failure (IIT). A write failure to EEPROM or a communication failure with EEPROM occurred.
062-355 RAP IPS Fan Failure. The IPS fan failed.
062-356 RAP IIT Lamp Fan Failure. An error signal was detected for the lamp fan.
062-357 RAP CCD Fan Failure. An error signal was detected for the CCD fan.
062-360 RAP Carriage Position Failure. A problem was detected with the carriage position.
062-362 RAP X Hard Failure
062-371 RAP Lamp Failure. It was detected that insufficient light from the lamp was entering the CCD (during white variation correction before the start of a scan, or during AGC).
062-380 RAP Platen AOC Failure. There was a failure during automatic gain correction (AGC).
062-386 RAP Platen AOC Failure. This was a failure during automatic offset correction (AOC).
062-389 RAP Carriage Over Run (Scan End). The carriage overran the scan end side.
062-392 RAP IIT/IPS Memory Failure. A failure was detected with the IIT/IPS PWB RAM (checked when power is turned on), or an internal processing error occurred in the IIT/IPS PWB.
062-393 RAP IIT/IPS PWB Failure. An internal processing error occurred in the IIT/IPS PWB.
062-500 RAP IISS-ROM data write error detected. (DLD system). Downloader Fail cannot be displayed on PWS.
062-790 RAP X Detect Failure. The original being read is an original for which copying is prohibited.
071-100 RAP Tray 1 Pre Feed Sensor is not turned On after paper is fed from Tray 1.
071-101 RAP Tray 1 Feed Out Sensor is not turned ON within the specified time after the start of feed from Tray 1.
071-102 RAP The Tray 1 Feed Out Sensor does not turn ON during paper transport on the Takeaway Path for the paper fed from Tray 1.
071-104 RAP Pre Registration Sensor ON Jam (Tray 1). The paper from Tray 1 did not turn on the Pre Registration Sensor within the specified time.
071-105 RAP Registration Sensor ON Jam (Tray 1). The paper from Tray 1 did not turn on the reg sensor within the specified time.
071-210 RAP Tray 1 Lift Up Failure. The Tray 1 Stack Height Sensor did not come on within the specified time after the tray was inserted.
072-100 RAP Tray 2 Pre Feed Sensor is not turned On after paper is fed from Tray 2.
072-101 RAP Tray 2 Misfeed Jam. Tray 2 Feed Out Sensor did not come on within the specified time after the start of feed for Tray 2.
072-102 RAP The Tray 2 Feed Out Sensor does not turn ON during paper transport on the Takeaway Path for the paper fed from Tray 2.
072-104 RAP Pre-Registration Sensor ON Jam (Tray 2). The paper from Tray 2 did not turn on the Pre Registration Sensor within the specified time.
072-105 RAP Registration In Sensor ON Jam (Tray 2). The paper from Tray 2 did not turn on the Reg In Sensor within the specified time.
072-210 RAP Tray 2 Lift Up Failure. The Tray 2 Stack Height Sensor did not come on within the specified time after the tray was inserted.
073-100 RAP Tray 3 Pre Feed Sensor is not turned On after paper is fed from Tray 3.
073-101 RAP Tray 3 Misfeed Jam. Tray 3 Feed Out Sensor did not come on within the specified time after the start of feed for Tray 3.
073-102 RAP Tray 3 Feed Out Sensor ON Jam. The paper from Tray 3 did not turn on Tray 3 Feed Out Sensor within the specified time.
073-104 RAP Pre Registration Sensor ON Jam (Tray 3). The paper from Tray 3 did not turn on the Pre Registration Sensor within the specified time.
073-105 RAP Registration Sensor ON Jam (Tray 3). The paper from Tray 3 did not turn on the Reg Sensor within the specified time.
073-210 RAP Tray 3 Lift Up Failure. The Tray 3 Stack Height Sensor did not come on within the specified time after the tray was inserted.
073-211 RAP Five consecutive failures in the Tray Size Sensor that monitors Tray 3 at intervals of 100ms have been detected.
075-100 RAP Tray 5 Pre Feed Sensor is not turned ON a spec time after the start of feed from Tray 5.
075-109 RAP Paper from Tray 5 does not turn ON Pre Reg. Sensor within a spec time.
075-135 RAP Paper from Tray 5 does not turn on the Reg. In Sensor within a spec time.
075-210 RAP Tray 5 Lift Up Sensor does not turn ON a spec time after Tray 5 starts lifting up.
075-211 RAP Tray 5 Lift Down Sensor does not turn ON a spec time after Tray 5 starts lowering.
077-103 RAP The Fuser Exit Sensor did not turn off within the specified time in straight exit mode.
077-106 RAP The Fuser Exit Sensor did not come on within the specified time after the registration motor came on.
077-107 RAP The Fuser Exit Sensor did not turn off within the specified time in invert exit mode.
077-109 RAP The IOT exit sensor did not come on at the specified time in non-invert mode. (Straight output)
077-111 RAP The IOT Exit Sensor did not come on within the specified time in invert exit mode.
077-112 RAP Regi Out SNR On Jam
077-113 RAP The IOT Exit Sensor did not turn off at the specified time in non-invert mode.
077-115 RAP The IOT Exit Sensor did not turn off within the specified time in invert exit mode.
077-118 RAP The paper transported from duplex did not turn on the Pre Registration Sensor within the specified time.
077-120 RAP Post 2nd BTR Sensor On JAM
077-121 RAP Post 2nd BTR Sensor Off JAM
077-123 RAP Regi In Sensor is not turned On after paper is fed from Duplex.
077-128 RAP Invert In Sensor is not turned ON within specified time in paper transport at Invert area.
077-129 RAP Paper transported from duplex did not turn on the Registration Sensor within the specified time.
077-130 RAP Duplex Out Sensor does not turn ON at specified time after Duplex In Sensor turns ON.
077-132 RAP Invert In Sensor is not turned Off within specified time in paper transport at Invert area.
077-143 RAP CIS Side Regi Error
077-145 RAP Lead Regi Error
077-220 RAP Side Shift Home Fail
077-222 RAP Pre Regi Release Fail
077-223 RAP Regi Release Fail
077-300 RAP The Front Cover is open.
077-301 RAP The Left Hand Interlock is open.
077-302 RAP The Right Hand Cover Interlock is open
077-303 RAP Transfer Module 2 Interlock Open.
077-304 RAP The Tray 5/Bypass Cover Interlock is open
077-311 RAP Invert Release Fail. Invert Release mechanical failure.
077-312 HCF RAP IOT-HCF Communication Failure
077-315 RAP CIS Subsystem Fail
077-320 RAP All Feed Trays Fail
077-325 RAP Pre Regi NIP Fail
077-326 RAP Regi NIP Fail
077-909 RAP IOT Static Jam
078-100 RAP The paper transported from Tray 6 did not turn on the Pre Registration Sensor within the specified time.
078-101 RAP The Tray 1 Feed Out Sensor did not come on within the specified time after the start of feed from Tray 6 (HCF).
078-102 RAP The paper transported from Tray 6 did not turn on the Registration Sensor within the specified time.
078-151 RAP The Tray 6 Feed Out Sensor did not come on within the specified time after the start of feed.
078-250 RAP HCF Tray Lift failure. The Tray 6 Stack Height Sensor does not turn ON within the specified time after the trays were inserted.
078-300 RAP The HCF Top Cover Interlock is open.
078-301 RAP HCF Docking Interlock Open. The HCF and the IOT were undocked.
078-500 RAP Error is detected in the processing of data write in HCF-ROM.(with DLD method). Error is detected during writing to HCF-ROM. ROM content is deleted, preventing M/C from operating normally.
078-901 RAP The tray 6 feed out sensor static jam.
089-315 RC CIS Subsystem Fail
089-600 RAP RC SampleLateral Fail-A1. FastScan Correction Failure #3 (Cyan) color FastScan position, a reference, has a failure when A1/C Patch detected.

[dastin]

часть четвертая

089-601 RAP RC SampleBlock Fail-A1-IN. The Inner MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment. MOB Sensor detection error or A1/C Patch creation failure. The specified number of effective sample blocks is not reached in MOB Sensor IN at A1/C Patch detection.
089-602 RAP RC SampleBlock Fail-A1-CNT. The CENTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment. MOB Sensor detection error or A1/C Patch creation failure. The specified number of effective sample blocks is not reached in MOB Sensor CENTER at A1/C Patch detection.
089-603 RAP RC SampleBlock Fail-A1-OUT. The OUTER MOB Sensor failed to detect the fine-adjustment patterns properly during fine adjustment. MOB Sensor detection error or A1/C Patch creation failure. The specified number of effective sample blocks is not reached in MOB Sensor OUT at A1/C Patch detection.
089-604 RAP RC SampleBlock Fail-B-#1-IN. MOB Sensor detection error or B Patch creation failure. The specified number of effective sample blocks is not reached in MOB Sensor IN at #1(Yellow) color B Patch detection.
089-605 RAP Refer to Printing CE Reports and print a Failure Report. Examine the report for any Chain 089 faults.
089-606 RAP Refer to Printing CE Reports and print a Failure Report. Examine the report for any Chain 089 faults.
089-607 RAP RC SampleBlock Fail-B-#2-IN. The INNER MOB Sensor failed to detect the rough-adjustment patterns correctly during Magenta rough adjustment. Refer to Printing CE Reports and print a Failure Report. Examine the report for any Chain 089 faults
089-608 RAP RC SampleBlock Fail-B-#2-CNT. The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment. Refer to Printing CE Reports and print a Failure Report. Examine the report for any Chain 089 faults
089-609 RAP RC SampleBlock Fail-B-#2-OUT. The OUTER MOB Sensor failed to detect the rough-adjustment patterns properly during Magenta rough adjustment.
089-610 RAP RC SampleBlock Fail-B-#3-IN. The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-611 RAP RC SampleBlock Fail-B-#3-CNT. The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-612 RAP RC SampleBlock Fail-B-#3-OUT. The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Cyan rough adjustment.
089-613 RAP RC SampleBlock Fail-B-#4-IN. The INNER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-614 RAP RC SampleBlock Fail-B-#4-CNT. The CENTER MOB Sensor failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-615 RAP RC SampleBlock Fail-B-#4-OUT. The MOB Sensor OUT failed to detect the rough-adjustment patterns properly during Black rough adjustment.
089-616 RAP RC Data OverFlow Fail. The calculated adjustment amount has exceeded the specifiable range.
089-617 RAP RC Data OverRange Fail. There was an error in the calculated adjustment value.
089-618 MOB LED Fail - In RAP
089-619 MOB LED Fail - Cnt RAP
089-620 MOB LED Fail - Out RAP
089-621 RC Temp Sensor Fail RAP
089-640 CIS Dark Level Error
089-641 CIS White Level Error
089-642 CIS LED Power Control Fail
089-643 CIS Shading Data Fail
089-644 CIS FPGA Fail
089-645 CIS Comm Fail
089-646 CIS SideEdge Detect Fail
089-647 CIS SideEdge Detect A Fail
089-648 CIS SideEdge Detect B Fail
089-649 CIS SideEdge Detect C Fail
089-650 CIS SideEdge Out of Range
089-651 CIS Shading Recommend
089-652 CIS Hard Fail
091-312 RAP CC HVPS Broken Fail. CC HVPS failure is detected.
091-313 RAP CRUM ASIC communication Failure
091-320 RAP Charge Corotron Wire is broken.
091-400 RAP The replacement date for Waste Toner Bottle (regular) is near.
091-403 RAP The Charge Corotron Assembly is near the end-of-life.
091-404 RAP The Charge Corotron Assembly has reached the end-of-life.
091-910 RAP The waste toner bottle is not present.
091-911 RAP The waste toner bottle is full.
091-913 RAP The Black drum cartridge (K) has reached the end-of-life.
091-914 RAP Communication failure between the MCU and the Black Drum CRUM
091-915 RAP The MCU detected incorrect data in the Black drum cartridge CRUM.
091-916 RAP The CRUM authentication registration data on the drum cartridge is incorrect.
091-917 RAP MCU cannot communicate with the CRUM in drum Y
091-918 RAP Communication failure with the Magenta Drum CRUM
091-919 RAP Communication failure with the Cyan Drum CRUM
091-920 RAP The MCU detected incorrect data in the Yellow drum cartridge CRUM.
091-921 RAP Drum K CRUM Not Position.
091-922 RAP Drum M CRUM Data Broken. Conflict between Write data and Read data to/from Drum M CRUM.
091-923 RAP Drum C CRUM Data Broken. Conflict between Write data and Read data to/from Drum C CRUM.
091-924 RAP The CRUM authentication registration data on the Yellow drum cartridge is incorrect.
091-925 RAP Wrong CRUM data in Magenta cartridge.
091-926 RAP The CRUM authentication registration data on the Cyan drum cartridge is incorrect.
091-927 RAP Yellow Drum CRUM is disconnected.
091-928 RAP Yellow Drum CRUM is disconnected.
091-929 RAP Cyan Drum CRUM is disconnected.
091-932 RAP The Yellow drum cartridge (Y) has reached the end-of-life.
091-933 RAP The Magenta drum cartridge (M) has reached the end-of-life.
091-934 RAP The Cyan drum cartridge (C) has reached the end-of-life.
091-600 Environment Temperature Fail RAP
091-601 Environment Humidity Fail RAP
092-649 RAP The MOB ADC Shutter remains open due to shutter failure.
092-650 RAP The MOB ADC Shutter remains closed due to shutter failure.
092-651 RAP The output read by ADC Sensor from the clean Photoreceptor surface is out of range (100~1000) (in Mini-Setup).
092-652 RAP The measured ADC Patch density is light. (Over 75% of Vclean)
092-653 RAP ATC SNR-Yellow output signal failure
092-654 RAP ATC SNR-Magenta output signal failure
092-655 RAP ATC SNR-Cyan output signal failure
092-656 RAP ATC SNR-black output signal failure
092-657 RAP The amplitude of ATC Yellow Sensor output is smaller (<10).
092-658 RAP The amplitude of ATC Magenta Sensor output is smaller (<10).
092-659 RAP The amplitude of ATC Cyan Sensor output is smaller (<10).
092-660 RAP The amplitude of ATC Black Sensor output is smaller (<10).
092-661 RAP The temperature output of the Humidity/Temperature Sensor was not in the appropriate range (140 ~ 896).
092-662 RAP The humidity output of the Humidity/Temperature Sensor was not in the appropriate range (30 ~ 607).
092-663 RAP Minisetup ADC Fail. This fault occurs when density difference between two patches created with MiniSetup is too small. Fail with each YMCK (752-202,203,204,205), Counter with each YMCK (195,196,197,198).
093-300 RAP Marking Drawer Interlock Open
093-313 RAP The Low Toner Sensor failed to detect any toner after the Toner Cartridge Motor operated for 20sec and aborted the refilling operation.
093-314 RAP Yellow Dispense failure.
093-315 RAP Magenta Dispense failure.
093-316 RAP Cyan Dispense failure.
093-317 RAP Black Dispense failure.
093-320 RAP There was a problem with the developer motor rotation.
093-600 RAP Yellow Dispense near failure.
093-601 RAP Magenta Dispense near failure.
093-602 RAP Cyan Dispense near failure.
093-603 RAP Black Dispense near failure.
093-912 RAP The Black Dispense Motor rotation timed out indicating that the Black Cartridge and Reserve Tank is empty.
093-918 RAP A communication failure with Black Toner Cartridge CRUM K2
093-924 RAP A communication failure with Black Toner Cartridge CRUM K1
093-925 RAP The data written to the toner CRUM K1 did not agree with the data read.
093-926 RAP Toner Cartridge CRUM K1 Authentication Data is different.
093-927 RAP A communication failure with Yellow Toner Cartridge CRUM Y
093-928 RAP A communication failure with Magenta Toner Cartridge CRUM M
093-929 RAP A communication failure with Cyan Toner Cartridge CRUM C
093-932 RAP Cartridge Exchange Time Over
093-933 RAP The data written to the toner CRUM Y did not agree with the data read.
093-934 RAP The data written to the toner CRUM M did not agree with the data read.
093-935 RAP The data written to the toner CRUM C did not agree with the data read.
093-936 RAP The data written to the toner CRUM K2 did not agree with the data read.
093-937 RAP Toner Cartridge CRUM Y Authentication Data is different.
093-938 RAP Toner Cartridge CRUM M Authentication Data is different.
093-939 RAP Toner Cartridge CRUM C Authentication Data is different.
093-940 RAP Toner Cartridge CRUM K2 Authentication Data is different.
094-320 RAP Retraction was not detected within the specified time (2400ms) after retraction of the 1st BTR started.
094-321 RAP First BTR Contact Failure.
094-322 RAP Second BTR Retract Failure.
094-323 RAP Contact was not detected within the specified time after contact with the 2nd BTR started.
102-356 RAP Fatal error related to the EWS. A problem occurred during software processing, and processing could no longer continue.
102-380 RAP Fatal error in the MF UI count. A problem occurred during software processing, and processing could no longer continue.
102-381 RAP There was notification of a scope initialization error on the ESS side, a message sending error, or an error obtaining the received data, during communication between ESS and the control panel.
102-382 RAP A required message was sent to the control panel and a verification message was not returned within the specified time, after a required parameter had not been attached from the control panel, or a problem with its length was detected for a variable length parameter.
103-310 RAP Common System Fail. Hybrid Water Mark Not Exist. Though "Hybrid Water Mark detection hardware available" is set with System Data, Hybrid Water Mark detection hardware cannot be detected. This Fail was originally defined with 16-312, however, it is newly registered to change category into System Fail according to the change of paper security kit installation operation.
103-311 RAP Common System Fail. Hybrid Water Mark Setting Mismatch. Hybrid Water Mark detection hardware is detected but System Data is not valid. This Fail was originally defined with 16-313, however, it is newly registered to change category into System Fail according to the change of paper security kit installation operation.
103-312 RAP Common System Fail. Hybrid Water Mark Not Exist (Back Side). Hybrid Water Mark detection hardware for Side2 of original document is not loaded, Paper Security Kit is not implemented. This Fail was originally defined with 16-314, however, it is newly registered to change category into System Fail according to the change of paper security kit installation operation.
103-313 RAP SW Option Fail (IISS Mem for HWM Not Exist). SW option function not achieved due to IISS Ext memory insufficiency, "Paper Security Kit" cannot be implemented. With HWM option function being set to Valid, "HWMIISS Ext Memory (Slot1:128MB Slot:128MB or more. Not Loaded" is detected.
112-700 RAP Puncher Waste Bin Near Full was detected.
116-210 RAP Media Reader Fatal Error
116-211 RAP Media Reader Cable disconnected
116-212 RAP [Media Reader] MediaLib SW Logic Failure
116-220 RAP Downloader Initialize Fail when going to Download mode. (When in normal mode or in Forced Download mode.)
116-310 RAP An error was detected while checking ESS font ROM DIMM #2.
116-311 RAP ESS Font ROM DIMM #3 Check Fail.
116-312 RAP An error was detected in the HDD encryption key during activation.
116-313 RAP An encryption key was specified but the HDD itself was not encrypted.
116-314 RAP An ethernet error was detected.
116-315 RAP An error was detected during System Memory DIMM #1 R/W.
116-316 RAP An error was detected during System Memory DIMM #2 R/W.
116-317 RAP An error was detected when checking the ESS DIMM #1 ROM.
116-318 RAP An error was detected when checking the expansion ESS DIMM #2 ROM.
116-319 RAP Loaded ROM and Panel config (FCW-UI or HB-UI) do not match each other.
116-321 RAP System Software Fatal Error. A problem occurred during software processing, and processing could no longer continue.
116-322 RAP WebDAV S/W Failure. A problem occurred during software processing, and processing could no longer continue.
116-323 RAP An error was detected during the ESS PWB NVM Read/Write Check. This fault will frequently appear immediately after replacing the ESS NVM PWB.
116-324 RAP A fatal software exception error has occurred in the Controller PWB CPU. The cause is most likely the Controller software failure.
116-325 RAP An error occurred in ESS fan rotation.
116-328 RAP Failure of Leve2 cache incorporated in CPU is detected.
116-329 RAP A system call error related to the serial I/F was detected.
116-330 RAP Error during the check of the HDD when the power was turned on, or the HDD was not formatted.
116-331 RAP An error related to the log was detected.
116-332 RAP An error in the MF ROM was detected.
116-333 RAP LocalTalk system call error.
116-334 RAP [ESS-NVRAM loaded as is factory shipping condition] or [ESS-NVRAM data illegal state] is detected by SystemCont during Read/Write check at Power ON. Just when 116-334 is detected, ESS-ROM initialize data starts to be written in ESS-NVRAM data. Therefore, at next Power Off/On, Inconsistency SystemFail(124-3xx).
116-336 RAP Redirector HD Failure. A problem was detected during HD access.
116-337 RAP Fatal error with SNTP in general. A problem occurred during software processing, and processing could no longer continue.
116-338 RAP Fatal error with JBA in general. A problem occurred during software processing, and processing could no longer continue.
116-340 RAP There was insufficient page memory, input buffers, or work area.
116-341 RAP The ROM DIMMs installed are incorrect versions or an invalid combination of ROM DIMMs are installed.
116-342 RAP Fatal error related to the SNMP agent. A problem occurred during software processing, and processing could no longer continue.
116-343 RAP An IC error within the ESS PWB was detected.
116-346 RAP Formatter failure. Error return from a system call.
116-348 RAP Redirector failure. Error return from a system call.
116-349 RAP There was an error with a call within SIF related to Pflite.
116-350 RAP Fatal error with AppleTalk in general. A problem occurred during software processing, and processing could no longer continue.
116-351 RAP Fatal error related to EtherTalk. A problem occurred during software processing, and processing could no longer continue.
116-352 RAP Fatal error related to NetWare. A problem occurred during software processing, and processing could no longer continue
116-353 RAP A physical problem was detected with the HDD during activation, causing the HDD not to activate.
116-354 RAP A problem with the HDD product code was detected during activation, so the HDD was not activated. A possibility exists that the HDD was formatted with a different model machine.
116-355 RAP Fatal error related to the SNMP agent. A problem occurred during software processing, and processing could no longer continue.
116-356 RAP The HDD was formatted, but either an incorrect HDD was connected or an HDD failure occurred.
116-357 RAP PostScript fatal system error. A problem occurred during software processing, and processing could no longer continue.
116-358 RAP Fatal error related to the salutation. A problem occurred during software processing, and processing could no longer continue.
116-359 RAP Fatal error in PLW. A problem occurred during software processing, and processing could no longer continue.
116-360 RAP Fatal error related to SMB. A problem occurred during software processing, and processing could no longer continue.
116-361 RAP SPL HDD fatal error. SpoolCont detected an error during HDD access.
116-362 RAP SSDP software failure. A problem occurred during software processing, and processing could no longer continue.
116-363 RAP BMLinkS or print service software failure. A problem occurred during software processing, and processing could no longer continue.
116-364 RAP A timer error was detected.
116-365 RAP SPL fatal error. A problem occurred during software processing, and processing could no longer continue.
116-366 RAP Report generator incorrect operation. A problem occurred during software processing, and processing could no longer continue.
116-367 RAP Parallel fatal error. A problem occurred during software processing, and processing could no longer continue.
116-368 RAP DumpPrint fatal error. A problem occurred during software processing, and processing could no longer continue.
116-370 RAP XJCL fatal error. A problem occurred during software processing, and processing could no longer continue.
116-371 RAP PCL Decomposer Software Failure. PCL fatal error. A problem occurred during software processing, and processing could no longer continue.
116-372 RAP P-Formatter fatal error. Problem occurs in software processing, which prevents the subsequent processing.
116-373 RAP Fatal error related to Dynamic DNS. A problem occurred during software processing, and processing could no longer continue.
116-374 RAP AutoSW fatal error. A problem occurred during software processing, and processing could no longer continue.
116-375 RAP I-Formatter Fail.
116-376 RAP Port 9100 Software Fail
116-377 RAP Video DMA Fail
116-378 RAP Fatal error related to MCR. A problem occurred during software processing, and processing could no longer continue.
116-379 RAP Fatal error related to MCC. A problem occurred during software processing, and processing could no longer continue.
116-380 RAP An error was detected while checking ESS Font ROM DIMM #1.
116-381 RAP It was detected that the AddressBookLibrary didn't agree with the ABL version information in NVM, or the data was corrupted.
116-382 RAP An AddressBookLibrary access to NVM or HDD failed.
116-383 RAP Image expansion kit (Ama+toto board) Not Loaded on Controller board is detected during job. Or Ama+toto board failure is detected during job. Or HDD access error occurs during job. Or 016-231 is detected at power on but this fault "is detected during job execution". Note that timing of fault occurrence is different.
116-384 RAP DCS Software Fail. Problem occurs in software processing, which prevents the subsequent processing.
116-385 RAP Fatal error related to the IDC. A problem occurred during software processing, and processing could no longer continue.
116-387 RAP MRC HW Fatal Error. Fatal error occurs while high-compression board is in used.
116-388 RAP It was detected that no HD is installed, although this is a configuration (there is a FAX) that requires an HD.
116-389 RAP The system detected that no additional RAM was installed though the system configuration (with HDD, etc.) required the installation of an additional RAM.
116-390 RAP A version mismatch was detected between the standard ROM and NVM.
116-391 RAP Incorrect specification of the country code, territory code, or paper size group.
116-393 RAP AAA Manager S/W Fail.
116-394 RAP Authentication mode and Counting mode setting failure detected in AAA Manager Boot sequence.
116-395 RAP Fatal error related to the USB. A problem occurred during software processing, and processing could no longer continue.
116-399 RAP M/C Initialization state still stays 10 minutes after startup. (Startup after recovery from Power Save is not included.)
116-701 RAP Duplex printing is not possible due to insufficient memory.
116-702 RAP Printing occurred with a substitute font.
116-703 RAP There was a problem with the PostScript data so that an error occurred during PostScript grammar interpretation or language interpretation.
116-704 RAP Media Reader No Insert (No Job)
116-705 RAP Media Reader Format Error (No Job)
116-706 RAP Media Reader: File Attribute Read Error (No Job)
116-707 RAP Media Reader: Image File Read Error (No Job
116-708 RAP Media Reader: File Attribute Read Error (In Job)
116-709 RAP Media Reader: Image File Read Error (Occurs during job)
116-710 RAP It is possible that the size of the original was not correctly determined because the incoming data exceeded the HP-GL/2 (option) spool size.
116-711 RAP The size and direction of the specified ART EX form do not agree with that of the paper to be printed.
116-712 RAP The PLW form/logo data cannot be registered due to insufficient RAM or HD space.
116-713 RAP The job was divided because the HDD was full.
116-714 RAP An HP-GL/2 (option) command error occurred.
116-715 RAP The form could not be registered because the PLW form registration upper limit was reached.
116-716 RAP Media Reader File Does Not Exist
116-717 RAP MediaLib: Not Execute of New Request
116-718 RAP The specified PLW form has not been registered.
116-720 RAP PCL Memory Low, Page Simplified
116-725 RAP Disk Full occurs in Log Image storage area.
116-737 RAP User defined data (foreign alphabet, pattern, etc.) could not be registered because there was insufficient ART IV user definition memory.
116-738 RAP Form overlay was not possible due to inconsistency between form imaging size/orientation and paper size/orientation. .
116-739 RAP Form/Logo data cannot be registered due to capacity shortage of RAM disk or hard disk.
116-740 RAP An arithmetic error occurred because the print data exceeded the printer limit.
116-741 RAP No more forms can be registered because the number of ART IV Forms registered has reached the upper limit.
116-742 RAP No more logo data can be registered because the number of ART IV log data registered has reached the upper limit.
116-743 RAP Received data (Form/Logo) exceeds registered buffer size.
116-745 RAP An ART IV command error occurred. During Decompose, the Decomposer checks for syntax error and values that exceed their respective limit values.
116-746 RAP The specified form has not been registered.
116-747 RAP The paper margin value is too large for the HP-GL/2 (option) effective coordinate area.
116-748 RAP The HP-GL/2 (option) print data does not contain any image data.
116-749 RAP The specified PostScript font is not in ROM or HDD.
116-752 RAP Print job ticket description warning.
116-771 RAP Invalid JBIG Parameter DL Fixed. A problem with the parameters included in the data was automatically corrected.
116-772 RAP Invalid JBIG Parameter D Fixed. A problem with the parameters included in the data was automatically corrected.
116-773 RAP Invalid JBIG Parameter P Fixed. A problem with the parameters included in the data was automatically corrected.
116-774 RAP Invalid JBIG Parameter YD Fixed. A problem with the parameters included in the data was automatically corrected.
116-775 RAP Invalid JBIG Parameter LO Fixed. A problem with the parameters included in the data was automatically corrected.
116-776 RAP Invalid JBIG Parameter MX Fixed. A problem with the parameters included in the data was automatically corrected.
116-777 RAP Invalid JBIG Parameter MY Fixed. A problem with the parameters included in the data was automatically corrected.
116-778 RAP Invalid JBIG Parameter VLENGTH Fixed. A problem with the parameters included in the data was automatically corrected.
116-780 RAP There was a problem with the document attached to the received mail.
116-790 RAP Stapling is canceled for all sets or only the top set to conduct printing..
118-310 RAP EPSV-Accessory Communication Fail. Internal error is detected during IPSEC initialization.
118-700 RAP Puncher Waste Bin Near Full was detected.
121-310 EPSV-Accessory Communication Fail
121-311 IC Card Auditron Config Fail 01
121-312 IC Card Auditron Config Fail 02
121-313 IC Card Auditron Config Fail 03
121-314 Customize User Prompts Fail
121-316 EP Accessory conflicts with SecureAccess
121-317 Continuous JOB Setting Missmatch of EPLyzer
121-318 Auth/Accout Settings Is Not Supported
121-319 Fax Send Charging and IFax Setting Confliction
121-322 EPA - Controller Unit Price Table Setting Error
121-323 Web EP Software Fail
121-324 Fax Send Charging And Scan Setting Confliction
121-333 EPSV-EP M/C Communication Fail
121-334 EPSV Login Fail
121-335 EPSV Wake Up Answer Fail
121-336 Unknown EP Accessory
121-337 EP Accessory Self Diag Fail
121-338 EPSV Answer Time Out
121-339 Changed Price Table Error
121-340 EP Accessory Miss Match
121-350 EPSV Logic Fail
121-370 EP-DX - Unexpected Error
123-200 RAP The data received from ESS exceeded the buffer size of the storage destination within the control panel.
123-201 RAP Data that was intended to be received from the control panel exceeded the buffer size of the storage destination within the control panel.
123-202 RAP Events occurred that exceeded the processing capability for requests generated within the control panel.
123-203 RAP UI Debug code
123-204 RAP SIO Parameter Failure (UI-Control panel). Serial communication error.
123-205 RAP SIO Command Failure (UI-Control panel). Serial communication error.
123-206 RAP SIO Status Failure (UI-Control panel). Serial communication error.
123-207 RAP Comm Manager Target Failure (UI-Control panel). Serial communication error.
123-208 RAP Comm Manager Command Failure (UI-Control panel). Serial communication error.
123-209 RAP EVM Returns Wrong Value (UI-Control panel). UI software error within the ESS PWB.
123-310 RAP Send Queue Full (UI-Control panel). The upper bound for the ability to send data from the control panel to ESS was exceeded.
123-311 RAP Receive Queue Full (UI-Control panel). The data received from ESS exceeded the upper boundary of the processing ability within the control panel.
123-312 RAP EVM Uses Wrong API (UI-Control panel). UI software error within the ESS PWB.
123-313 RAP AS Uses Wrong API (UI-Control panel). UI software error within the ESS PWB.
123-314 RAP Event-Waiting Timer Timeout (UI-Control panel). There was no notification of a reply message from ESS within the specified time.
123-315 RAP CTS Internal Failure (UI-Control panel). UI software error within the ESS PWB.
123-316 RAP Send Request Queue Full SIO (UI-Control panel). The upper boundary for the ability to send data from the control panel to ESS was exceeded.
123-317 RAP Receive Message Queue Full (UI-Control panel). The data received from ESS exceeded the upper boundary of the processing ability within the control panel.
123-318 RAP Receive Finish Queue Full (UI-Control panel). The data received from ESS exceeded the upper boundary of the processing ability within the control panel.
123-319 RAP Send Failure with No ACK (UI-Control panel). Serial communication error.
123-320 RAP Polling Failure (UI-Control panel). Serial communication error.
123-321 RAP Send Message Failure (UI-Control panel). Serial communication error.
123-322 RAP Target Failure (UI-Control panel). Serial communication error.
123-323 RAP Address Failure (UI-Control panel). Serial communication error.
123-324 RAP Size Failure (UI-Control panel). Serial communication error.
123-325 RAP Object Creation Failure (UI-Control panel). UI software error within the ESS PWB.
123-326 RAP Memory Overflow (UI-Control panel). UI software error within the ESS PWB.
123-327 RAP Button Overflow (UI-Control panel). UI software error within the ESS PWB.
123-328 RAP UI Internal Failure with Out of Area. UI software error within the ESS PWB.
123-329 RAP UI Internal Failure with Invalid Coordinates. UI software error within the ESS PWB.
123-330 RAP Interface Failure with Invalid Parameter LCD. UI software error within the ESS PWB.
123-331 RAP UI Internal Failure with Invalid LED Request. UI software error within the ESS PWB.
123-332 RAP I/F Failure (Invalid Parameter CP). UI software error within the ESS PWB.
123-333 RAP I/F Failure (No Communication). H/W connection failure within the UI Interface PWB, or an internal connection could not be corrected detected.
123-334 RAP I/F Failure (Receiving Error Key Code). UI software error within the ESS PWB.
123-335 RAP I/F Failure (Receiving Invalid Coordinates). UI software error within the ESS PWB.
123-336 RAP I/F Failure (DM-ACD Drv. I/F). UI software error within the ESS PWB.
123-337 RAP Frame Data Error with Invalid Data Type. UI software error within the ESS PWB.
123-338 RAP Frame Data Error Offset Address Out. UI software error within the ESS PWB.
123-339 RAP Display Request Code Invalid. UI software error within the ESS PWB.
123-340 RAP Interface Failure GUAM-DM I/F. UI software error within the ESS PWB.
123-341 RAP Event Queue Full (UI-Control panel). UI software error within the ESS PWB.
123-342 RAP Event Queue Empty (UI-Control panel). UI software error within the ESS PWB.
123-343 RAP Invalid Class (UI-Control panel). UI software error within the ESS PWB.
123-344 RAP Invalid Type (UI-Control panel). UI software error within the ESS PWB.
123-345 RAP Timer Queue Full (UI-Control panel). UI software error within the ESS PWB.
123-346 RAP Invalid Timer Number (UI-Control panel). UI software error within the ESS PWB.
123-347 RAP Undefined Trap (UI-Control panel). UI software error within the ESS PWB.
123-348 RAP Command Access Exception (UI-Control panel). UI software error within the ESS PWB.
123-349 RAP Invalid Command (UI-Control panel). UI software error within the ESS PWB.
123-350 RAP Privilege Command (UI-Control panel). UI software error within the ESS PWB.
123-351 RAP No FPU Exception (UI-Control panel). UI software error within the ESS PWB.
123-352 RAP Address Mis-align (UI-Control panel). UI software error within the ESS PWB.
123-353 RAP Data Access Exception (UI-Control panel). UI software error within the ESS PWB.
123-354 RAP Tag Overflow (UI-Control panel). UI software error within the ESS PWB.
123-355 RAP No Co Processor Exception (UI-Control panel). UI software error within the ESS PWB.
123-356 RAP Short of Area (UI-Control panel). UI software error within the ESS PWB.
123-357 RAP Cancel Wait Status (UI-Control panel). UI software error within the ESS PWB.
123-358 RAP Timeout (UI-Control panel). UI software error within the ESS PWB.
123-359 RAP Queue Overflow (UI-Control panel). UI software error within the ESS PWB.
123-360 RAP Context Failure (UI-Control panel). UI software error within the ESS PWB.
123-361 RAP Object Failure (UI-Control panel). UI software error within the ESS PWB.
123-362 RAP No Object (UI-Control panel). UI software error within the ESS PWB.
123-363 RAP Invalid ID (UI-Control panel). UI software error within the ESS PWB.
123-364 RAP Parameter Failure (UI-Control panel). UI software error within the ESS PWB.
123-365 RAP Reserve Attribute (UI-Control panel). UI software error within the ESS PWB.
123-366 RAP Reserve Function Code (UI-Control panel). UI software error within the ESS PWB.
123-367 RAP Unsupported Function (UI-Control panel). UI software error within the ESS PWB.
123-368 RAP Short of UI Memory (UI-Control panel). There is insufficient memory or a connection problem.
123-369 RAP Invalid Interface Value (UI-Control panel). UI software error within the ESS PWB.
123-370 RAP Interface Length Failure (UI-Control panel). There was a mistake in a parameter received from ESS.
123-371 RAP Interface Parameter Failure (UI-Control panel). There was a mistake in a parameter received from ESS.
123-372 RAP Interface Sequence Failure (UI-Control panel). There was no notification of an initialization command from ESS within the specified time.
123-373 RAP Channel Failure (UI-Control panel). There was a mistake in a cancel received from ESS.
123-374 RAP Invalid User Job ID (UI-Control panel). There was an error in a job ID parameter received from ESS.
123-375 RAP Internal Resource Failure (UI-Control panel). UI software error within the ESS PWB.
123-376 RAP Internal Memory Failure (UI-Control panel). UI software error within the ESS PWB.
123-377 RAP UI Timer Failure (UI-Control panel). UI software error within the ESS PWB.
123-378 RAP Interface Format Failure (UI-Control panel). There was an error in a data format received from ESS.
123-379 RAP Dispatch Failure (UI-Control panel). UI software error within the ESS PWB.
123-380 RAP Copy Interface Failure (UI-Control panel). UI software error within the ESS PWB.
123-382 RAP Scanner Interface Failure (UI-Control panel). UI software error within the ESS PWB.
123-383 RAP Report Interface Failure (UI-Control panel). UI software error within the ESS PWB.
123-384 RAP Server Access Failure (UI-Control panel). UI software error within the ESS PWB.
123-385 RAP Service Object Overflow (UI-Control panel). UI software error within the ESS PWB.
123-386 RAP Invalid Service Object (UI-Control panel). UI software error within the ESS PWB.
123-387 RAP Invalid Service Object Attribute (UI-Control panel). UI software error within the ESS PWB.
123-388 RAP Attribute Failure (UI-Control panel). UI software error within the ESS PWB.
123-389 RAP Argument Failure (UI-Control panel). UI software error within the ESS PWB.
123-390 RAP Job Parameter Failure (UI-Control panel). UI software error within the ESS PWB.
123-391 RAP Job Actual Parameter Failure (UI-Control panel). UI software error within the ESS PWB.
123-392 RAP Auditron Failure (UI-Control panel). UI software error within the ESS PWB.
123-393 RAP EP Failure (UI-Control panel). UI software error within the ESS PWB.
123-394 RAP File Access Failure (UI-Control panel). UI software error within the ESS PWB.
123-395 RAP NVM Failure (UI-Control panel). UI software error within the ESS PWB.
123-396 RAP FF Failure (UI-Control panel). UI software error within the ESS PWB.
123-397 RAP MGR Failure (UI-Control panel). UI software error within the ESS PWB.
123-398 RAP Delay Release Queue Full (UI-Control panel). UI software error within the ESS PWB.
123-399 RAP Internal Failure (UI-Control panel). UI software error within the ESS PWB.
123-400 RAP Internal Failure (UI-Control panel). Insufficient registration, internal error, or an IF sequence or parameter outside the specification was input to the converter.
124-310 RAP The product number was not specified.
124-311 RAP The serial number registration field failed.
124-312 RAP Product numbers did not agree.
124-313 RAP Serial numbers did not agree.
124-314 RAP IOT Speed Failure
124-315 RAP IOT Speed Mismatch
124-316 RAP Product a/f Model Failure
124-317 RAP Product a/f All Product Model Mismatch
124-318 RAP Product Type for S/W Key Failure
124-319 RAP All Product Type For S/W Key Mismatch
124-320 RAP EEP ROM Failure. A EEP ROM write problem occurred on the ESS PWB.
124-321 RAP Backup SRAM Failure. An NVM ROM write problem occurred on the ESS PWB.
124-322 RAP Copy/Scan/Print S/W Key by PWE Failure
124-323 RAP Copy/Scan/Print S/W Key 1 Failure
124-324 RAP All Billings Mismatch
124-325 RAP Billing Restoration Failure. Billing automatic recovery was not possible.
124-326 RAP IOT Speed Not Registered. Status 1 or 2 of speed registration procedure for IOT is detected when the system is booted.
124-327 RAP IOT Speed Change SW Fail. Status 1 or 2 of speed registration procedure for IOT is detected when the system is booted.
124-333 RAP ASIC Failure (Panther). A panther error was detected.
124-334 RAP Standard Font ROM Error. A problem was detected with the standard installed font ROM.
124-335 RAP Font ROM Not Found. The font ROM could not be detected.
124-337 RAP ESS Standard RAM Error. An error was detected with the ESS installed standard RAM.
124-338 RAP Same Font ROMs Found. It was detected that identical font ROMs were installed.
124-339 RAP ROM DIMM of another product found. It was detected that a different type of font ROM was installed.
124-340 RAP The three CRUM market destination values are not set up (0 or different).
124-341 RAP One CRUM market destination value is different (IOT).
124-342 RAP One CRUM market destination value is different (SYS 1).
124-343 RAP One CRUM market destination value is different (SYS 2).
124-350 RAP The three CRUM OEM destination values are not set up (0 or different).
124-351 RAP One CRUM OEM destination value is different (IOT).
124-352 RAP One CRUM OEM destination value is different (SYS 1).
124-353 RAP One CRUM OEM destination value is different (SYS 2).
124-360 RAP CRUM Valid/Invalid is not set up at the three locations (0 or different values).
124-361 RAP CRUM Validation Failure MCU. CRUM valid/invalid data was different (IOT).
124-362 RAP CRUM Validation Failure SYS 1. CRUM valid/invalid data was different (SYS 1).
124-363 RAP CRUM Validation Failure SYS 2. CRUM valid/invalid data was different (SYS 2).
124-372 RAP IOT sc Soft Failure. IOT controller software problem. A problem occurred during software processing, and processing could no longer continue.
124-373 RAP IOT Manager SW Failure. IOT manager software failure.
124-374 RAP IOT IM Device Driver software failure.
124-380 RAP CRUM Market fail ALL (2)
124-381 RAP CRUM Market fail MCU (2)
124-382 RAP CRUM Market fail SYS 1 (2)
124-383 RAP CRUM Market fail SYS 2 (2)
124-390 RAP CRUM OEM fail ALL (2)
124-391 RAP CRUM OEM fail MCU (2)
124-392 RAP CRUM OEM fail SYS 1 (2)
124-393 RAP CRUM OEM fail SYS 2 (2)
124-701 RAP Side Tray to Center Tray. The exit destination was changed to the center tray because there was a problem with the specified exit tray (side tray).
124-704 RAP The output tray was changed from the Folder Tray to the Center Tray and printing continued.
124-705 RAP Punching Cancelled. A punch specification was deleted.
124-706 RAP Folding Cancelled. A folding specification was deleted.
124-708 RAP The output tray has been changed to the Sub Tray because a failure was detected in the specified output tray.
124-709 RAP Stapler Sheet Count is too high.
125-311 RAP PSWcont Unexpected Failure. A problem occurred during ESS software (PST cont) processing, and processing could no longer continue.
127-210 RAP Network Controller detected DFE Communication Failure
127-211 RAP Network Controller DFE Parameter Error
127-212 RAP ExtPrint Check Mode Error
127-213 RAP External Print IF Mismatch
127-220 RAP Communication Error (video) detected by the Network Controller.
127-221 RAP DFE Communication Error (Command) detected by the Network Controller.
127-310 RAP ESR Task Fatal Error. An ESR task caused a fatal error.
127-311 RAP ExtPRT
127-312 RAP DFE Detection Video Link Fail
127-313 RAP ESS Detection Video Link Fail
127-314 RAP WSD Detection Video Link Fail
127-320 RAP Network Controller Critical Failure
127-337 RAP Job Template HDD Write Error. Internal polling file access error, or a write error to a local HDD in a job template (other than full).
127-342 RAP Job Template Monitor Failure. Error return from a system call, etc.
127-353 RAP LPD Soft Fatal Error. Fatal error related to LPD. A problem occurred during software processing, and processing could no longer continue.
127-354 RAP FTP Server Software Failure. FTP server fatal error.
127-396 RAP Mail I/O Soft Fatal error. Fatal error related to mail IO. A problem occurred during software processing, and processing could no longer continue.
127-398 RAP IPP Soft Fatal Error. Fatal error related to IPP. A problem occurred during software processing, and processing could no longer continue.
127-399 RAP JME Soft Fatal Error. Fatal error related to JME. A problem occurred during software processing, and processing could no longer continue.
133-210 RAP Fax-related SysFail. Fax Parameter Invalid. (Error of interface itself such as excess of length). Mandatory parameter is not reported. Note: Some Host resets Fax Card without returning this error.
133-211 RAP Fax-related SysFail. Fax Parameter Value Invalid. PV exceeds the specified range.
133-212 RAP Fax-related SysFail. Fax Read Error- No Data. Designated data does not exist. (Number/Channel illegal.)
133-213 RAP Fax-related SysFail. Fax Read Error- Invalid Data. Designated data cannot be read for some reason such as broken data. Host sometimes handles this failure as SystemFail
133-214 RAP Fax-related SysFail. USB Open Failure at Initialize. Detected by FAPE(createInstanceFail).
133-215 RAP Fax-related SysFail. Fax USB Device Fatal Error. FAPE informed with asynchronous event. .
133-216 RAP Fax-related SysFail. Fax USB Host Fatal Error. FAPE informed with asynchronous event. .
133-217 RAP Fax-related SysFail. Fax Manager Short of Memory. FAPE informed with asynchronous event. (Not defined currently).
133-218 RAP Fax-related SysFail. Fax Card Message Library Short of Memory. FAPE informed with asynchronous event. (Not defined currently).
133-219 RAP Fax-related SysFail. Fax Short of Work Memory. Failed to ensure the necessary memory space due to Memory Insufficient.
133-220 RAP Fax-related SysFail. Fax Cont S/W Fail. Fax Cont software processing problem occurs. After that, processing cannot continue.
133-221 RAP Fax-related SysFail. Fax Card No Response on Booting. Fax Card does not make any response for a certain time at Boot.
133-222 RAP Fax-related SysFail. Fax Card does not respond for a certain period.
133-223 RAP Fax-related SysFail. Fax Card Reset.
133-224 RAP Fax-related SysFail. Controller ROM Fax Card ROM Version Mismatch.
133-226 RAP Fax-related SysFail. Illegal country code for Fax. Country Code in system data includes the code where FAX service is not provided.
133-280 RAP Fax-related SysFail. Fax Option Slot1 Board Fail. Following processing/operation cannot continue due to FaxCard failure or FaxCont SW failure.
133-281 RAP Fax-related SysFail. Unknown message received. Fax Option Slot1 Board Fail. Message not specified in I/F Specification has been received from FaxCard.
133-282 RAP Fax-related SysFail. Fax Card download fail. Following processing/operation cannot continue because Fax Card Download is not completed normally due to FaxCard failure or FaxCont SW failure.
133-283 RAP Fax-related SysFail. FAX Report Mailbox not opened. When storage of FAX Report is attempted, Mailbox Not Open is found. .
134-210 RAP Fax Cont Parameter Invalid. Parameter value is not proper. (Interface error such as Value out of PV range designated, Length too long, etc.) Mandatory parameter is not sent.
134-211 RAP Fax Card Main Board Failure.
202-399 RAP Timer Internal Fail
500-030 RAP Timer Internal Failure. The following occurs (However, this includes the cases that may not occur when Print Test Pattern starts
500-990 RAP Printing could not start due to unknown reason in Diagnostic Code Test Pattern Print, or it was aborted. (Only end response) This occurs during Diagnostic execution only, and the Fault Code is displayed on the PC-Diagnostics and Panel.
OF-01 Common System Fail
OF-02 HDD System Fail
OF-03 NET/USB System Fail
OF-04 Panel System Fail
OF-05 IIT System Fail
OF-06 IOT System Fail
OF-07 FAX System Fail
OF-08 116-324 Fail
OF-09 Common Job Fail
OF-10 HDD Job Fail
OF-11 FAX Job Fail
OF-12 033-363 Fail
OF-13 016-782 / 016-784 Fail
OF-14 FAX Card Fail
OF 3.1 Network Controller Checkout RAP
OF 8.1 Paper Feed Checkout RAP
OF 9.1 Regi Measuring Cycle Failed RAP
OF-15 Chain-Link No. RAP
OF 99-1 Reflective Sensor RAP
OF 99-2 Transmissive Sensor
OF 99-3 Switch
OF 99-4 Generic Solenoid/Clutch RAP
OF 99-6 2 Wire Motor Open
OF 99-7 2 Wire Motor On
OF 99-8 Set Gate Solenoid Open
OF 99-9 Multiple Wire Motor
OF 1.1 Power RAP
OF 1.2 AC Power RAP
OF 1.3 AC Protect Circuit RAP
OF 2.1 IOT DC Power (+3.3/+5/+12 VDC) RAP
OF 2.2 IOT DC Power (+24VDC) RAP
OF 2.3 IIT DC Power RAP
OF 2.4 DADF DC Power RAP

[dastin]

часть пятая - Ошибки LP finisher

012-100 Decurler In Sensor ON Jam
012-101 Decurler Out Sensor ON Jam
012-102 Punch Out Sensor ON Jam
012-103 Punch Out Sensor OFF Jam
012-104 Interposer Feed Out Sensor ON Jam
012-105 Interposer Exit (Decurler Out Sensor) ON Jam
012-107 Folder Ent SNR OFF Jam
012-108 Folder Path Sensor-3 OFF Jam
012-109 Interposer Feed Out Sensor OFF Jam
012-113 Booklet In Sensor ON Jam
012-114 Booklet In Sensor OFF Jam 1
012-115 Booklet Folder Roll Exit Sensor ON Jam
012-116 Folder Ent SNR ON Jam
012-117 Folder Exit Sensor ON Jam
012-118 Folder Path Sensor 2 ON Jam
012-119 Folder Path Sensor 3 ON Jam
012-120 Folder Path Sensor 4 ON Jam
012-141 Buffer Path Sensor OFF Jam
012-142 Buffer Path Sensor ON Jam
012-151 Compile Exit Sensor OFF Jam
012-152 Compile Exit Sensor ON Jam
012-159 Eject Sensor ON Jam
012-160 Eject Sensor OFF Jam
012-161 Set Eject Jam
012-171 Top Tray Exit Sensor ON Jam
012-172 Top Tray Exit Sensor OFF Jam
012-180 Booklet Folder Roll Exit Sensor OFF Jam
012-211 Stacker Tray Fail
012-212 Stacker Tray Upper Limit Fail
012-213 Stacker Tray Lower Limit Fail
012-214 End Wall Home Sensor OFF Fail
012-215 End Wall Open Sensor ON Fail
012-216 End Wall Home Sensor ON Fail
012-217 End Wall Open Sensor OFF Fail
012-218 Shelf Home Sensor ON Fail
012-219 Shelf Home Sensor OFF Fail
012-221 Tamper Home Sensor On Fail
012-223 Tamper Home Sensor OFF Fail
012-225 Booklet Tamper Front Home Sensor ON Fail
012-226 Booklet Tamper Front Home Sensor OFF Fail
012-227 Booklet End Guide Home Sensor OFF Fail
012-228 Booklet End Guide Home Sensor ON Fail
012-229 Booklet Tamper Rear Home Sensor ON Fail
012-230 Booklet Tamper Rear Home Sensor OFF Fail
012-235 Staple Move Home Sensor ON Fail
012-236 Staple Move Home Sensor OFF Fail
012-237 Staple Center Position Sensor ON Fail
012-238 Staple Center Position Sensor OFF Fail
012-239 Sub Paddle Home Sensor ON Fail
012-240 Sub Paddle Home Sensor OFF Fail
012-241 Booklet Knife Folding Sensor Fail
012-243 Booklet Knife Home Sensor ON Fail
012-246 Booklet Stapler Fail
012-247 Side Regi Sensor OFF Fail
012-248 Compile Stacker Tray Offset Fail
012-250 End Guide Motor 1 Start Fail
012-251 End Guide Motor 2 Start Fail
012-252 End Guide Motor 1 Home Fail
012-253 End Guide Motor 2 Home Fail
012-254 Envelope Folder Tray Broken
012-255 Interposer Tray Up Fail
012-260 Eject Clamp Up Sensor ON Fail
012-264 Booklet Drawer Broken Fail
012-265 Booklet Knife Home Sensor OFF Fail
012-282 Eject Clamp Up Sensor OFF Fail
012-291 Stapler Fail
012-302 Finisher Front Door Interlock Open
012-304 I/F Module Front Door Interlock Open
012-306 Interposer Top Cover Open
012-307 Booklet Drawer Set Fail
012-320 Punch Home Sensor ON Fail
012-321 Punch Home Sensor OFF Fail
012-322 Puncher Move Home Sensor OFF Fail
012-323 Puncher Move Home Sensor ON Fail
012-324 Side Regi Home Sensor OFF Fail
012-325 Side Regi Home Sensor ON Fail
012-330 Decurler Cam Home Sensor OFF Fail
012-332 Decurler Cam Home Sensor ON Fail
012-334 Download Mode Fail
012-400 Staple Dust Near Full
012-500 Downloader Fail
012-900 Paper Remain at Buffer Path SNR Jam
012-903 Paper Remain at Compile Exit SNR Jam
012-905 Paper Remain at Set Compile Tray No Paper SNR Jam
012-907 Paper Remain at Top Tray Exit SNR Jam
012-908 Paper Remain at Eject SNR Jam
012-909 Punch Out Sensor Static Jam
012-938 Decurler In Sensor Static Jam
012-939 Decurler Out Sensor Static Jam
012-949 Punch Box Set Fail
012-952 Envelope Folder Tray Pause Detect
013-900 Interposer Feed Out Sensor Static Jam
013-902 Booklet Compile No Paper Sensor Static Jam
013-903 Booklet Folder Roll Exit Sensor Static Jam
013-905 Folder Exit Sensor Static Jam
013-906 Folder Path Sensor 1 Static Jam
013-907 Folder Path Sensor 2 Static Jam
013-908 Folder Path Sensor 3 Static Jam
013-909 Folder Path Sensor 4 Static Jam
OF1 Intermittent Fault RAP
OF2 Other Faults RAP
OF3 Audible Noise RAP
OF-15 Chain-Link No. RAP
OF 99-1 Reflective Sensor RAP
OF 99-2 Transmissive Sensor
OF 99-3 Switch
OF 99-4 Generic Solenoid/Clutch RAP
OF 99-6 2 Wire Motor Open
OF 99-7 2 Wire Motor On
OF 99-8 Set Gate Solenoid Open
OF 99-9 Multiple Wire Motor
------------------------------
------------------------------

[dastin]

часть шестая - High Capacity Stacker

049-100 Top Tray Exit SNR On Jam
049-101 Top Tray Exit SNR Off Jam
049-102 Top Tray Path SNR On Jam
049-104 Bypass Exit SNR On Jam
049-106 Bypass Exit SNR On Jam (Purge Enable)
049-108 Bypass Path SNR 1 On Jam
049-113 Stacker Path SNR On Jam
049-114 Stacker Path SNR Off Jam
049-115 Stacker Exit SNR On Jam
049-116 Stacker Exit SNR Off Jam
049-117 Bypass Path SNR 2 On Jam
049-119 Bypass Path SNR 2 On Jam (Purge Enable)
049-121 Stacker Exit SNR Off Jam (Purge Enable)
049-210 F-Door Lock SNR On Fail
049-211 F-Door Lock SNR Off Fail
049-212 Stacker Up Fail
049-213 Stacker Down Fail
049-214 Dolly Set Position SNR On Fail
049-215 Dolly Set Position SNR Off Fail
049-216 Stack Full SNR On Fail
049-217 Stack Full SNR Off Fail
049-218 Stack Height SNR On Fail
049-219 F-Door SW Fail
049-220 Stacker Upper Limit Fail
049-221 Stacker Lower Limit Fail
049-224 Paper In Edge SNR Initialize Fail
049-225 Paper Out Edge SNR Initialize Fail
049-228 Lead Tamper Home SNR On Fail
049-229 Lead Tamper Home SNR Off Fail
049-232 Set Clamper Home SNR On Fail
049-233 Set Clamper Home SNR Off Fail
049-234 Side Tamper Extension Home SNR On Fail
049-235 Side Tamper Extension Home SNR Off Fail
049-236 Rear (In) Tamper Home SNR On Fail
049-237 Rear (In) Tamper Home SNR Off Fail
049-238 Front (Out) Tamper Home SNR Off Fail
049-239 Front (Out) Tamper Home SNR Off Fail
049-240 Pad Move Home SNR On Fail
049-241 Pad Move Home SNR Off Fail
049-242 Exit Roll Home SNR On Fail
049-243 Exit Roll Home SNR Off Fail
049-248 P-Edge Home SNR On Fail
049-251 Fan Paper 1 SNR Fail
049-252 Fan Paper 2 SNR Fail
049-253 Fan Upper 1 SNR Fail
049-280 GATE 1 SNR Fail 1
049-281 GATE 1 SNR Fail 2
049-282 GATE 2 SNR Fail 1
049-283 GATE 2 SNR Fail 2
049-284 P-Edge Home SNR Off Fail
049-285 EEPROM Read/Write Error
049-286 EEPROM SUM Error
049-287 System Error
049-288 PWBA DRV Not Connected
049-300 UPPER COVER SW Open
049-310 HCS Download Mode Fail
049-500 RAP
049-700 Media Type NG
049-900 Paper Remain at Top Tray Exit SNR
049-901 Paper Remain at Top Tray Path SNR
049-902 Paper Remain at Bypass Exit SNR
049-903 Paper Remain at Bypass Path SNR 1
049-905 Paper Remain at Stacker Path SNR
049-907 Paper Remain at Stacker Exit SNR
049-908 Paper Remain at Bypass Path SNR 2
049-940 F-Door SW Open
049-941 Tray Set Fail
049-945 Top Tray Full
049-960 Stacker ABN Up SNR OFF Fail
049-964 Stack Height Control Sensor ON Fail
049-965 Stacker Sheet Count Full Stack Detection
049-967 Paper Remain at Stacker Tray
049-968 Mix Size Stacker Full Detection
049-969 Elevator Motor Step Out
049-970 Stacker Up LIM SNR Fail
049-971 Stacker Full Stack
049-972 Stacker Middle Stack
OF-15 Chain-Link No. RAP

[dastin]

часть седьмая - interface module

048-100 IFM Decurler In SNR On Jam (IOT)
048-101 IFM Decurler In SNR On Jam (Interposer)
048-102 IFM Exit SNR On Jam
048-104 IFM Feed Out SNR On Jam
048-105 IFM Feed Out SNR Off Jam (Purge)
048-106 IFM Feed Out SNR Off Jam (No Purge)
048-107 IFM Transport SNR On Jam
048-210 IFM Interposer Tray Up Fail
048-211 HCS 2 Communication Fail
048-213 Tape Binder Communication Fail
048-214 Perfect Binder Communication Fail
048-300 IFM Front Door Open
048-301 IFM Interposer Top Cover Open
048-310 IFM Decurler Cam Position 1 SNR On Fail
048-311 IFM Decurler Cam Position 1 SNR Off Fail
048-312 IFM Decurler Cam Position 2 SNR On Fail
048-313 IFM Decurler Cam Position 2 SNR Off Fail
048-314 IFM Decurler Gate SNR On Fail
048-315 IFM Decurler Gate SNR Off Fail
048-316 IFM Decurler Belt Mot Fail
048-318 IFM Cooling Fan1/2 Fail
048-319 IFM Cooling Fan3/4 Fail
048-320 HCS 1 Communication Fail
048-321 D-Finisher Communication Fail
048-322 Output Config Mismatch Fail
048-323 Interface Module Download Mode Fail
048-324 ICP Communication Fail
048-900 Paper Remain at IFM Decurler In SNR On
048-901 Paper Remain at IFM Exit SNR On
048-902 Paper Remain at IFM Feed Out SNR On Jam
048-903 Paper Remain at IFM Transport SNR On Jam
OF-15 Chain Link No. Rap
OF-16 In-line Spectrophotometer Fail RAP (770 DCP Only)

[dastin]

часть восьмая - hcf_3 и hcf_3.2

hcf_3

078-102 (HCF2) Regi Sensor On Jam
078-103 (HCF2) Exit Sensor On Jam
078-105 (HCF2 MSI) Pre Feed Sensor ON Jam
078-106 (HCF3) Pre Feed Sensor On Jam
078-110 (HCF2) Pre Regi Sensor On Jam
078-111 (HCF2) Regi Sensor On Jam
078-120 (HCF2) MSI Feed Out Sensor On Jam
078-151 (HCF3) Feed Out Sensor On Jam (Tray 6)
078-260 (HCF3) Lift Up Fail
078-261 (HCF3) Shift Mechanical Fail
078-262 (HCF3) Humidity Sensor Fail
078-263 (HCF3) Temp Sensor Fail
078-264 (HCF3) Lead Blower Fail
078-265 (HCF3) End Blower Fail
078-266 (HCF3) Front Blower Fail
078-267 (HCF3) Rear Blower Fail
078-268 (HCF3) Lead Shutter Fail
078-269 (HCF3) End Shutter Fail
078-270 (HCF3) Lead Heater Fail
078-271 (HCF3) Lead Heater Temp Sensor Fail
078-272 (HCF3) TIFF PWB F1 Fuse Fail
078-273 (HCF3) OHCF PWB F2 Fuse Fail
078-274 (HCF3) OHCF PWB F3 Fuse Fail
078-275 (HCF3) OHCF PWB F6 Fuse Fail
078-276 (HCF3) OHCF PWB F7 Fuse Fail
078-277 (HCF3) OHCF PWB F8 Fuse Fail
078-278 (HCF3) OHCF PWB F9 Fuse Fail
078-279 (HCF3) OHCF PWB F10 Fuse Fail
078-280 (HCF3) OHCF PWB F13 Fuse Fail
078-281 (HCF3) OHCF PWB Fuse Fail
078-282 (HCF3) MSI Lift Up Fail
078-283 (HCF3) MSI Down Fail
078-302 (HCF2) MSI Interlock Open
078-303 (HCF3) Front Cover Interlock Open
078-500 HCF-ROM Fail
078-900 (HCF2) Feed Out Sensor Static Jam (Tray 6)
078-902 (HCF2/OHCF) MSI Feed Out Sensor Static Jam
078-904 (HCF2/HCF3) Exit Sensor Static Jam
078-940 (HCF3) Paper Miss Set
078-941 (HCF3) Paper Size Mismatch
OF 2.5 HCF3 DC POWER RAP
OF1 Intermittent Fault RAP
OF2 Other Faults RAP
OF3 Audible Noise RAP
OF-15 Chain-Link No. RAP
OF 99-1 Reflective Sensor RAP
OF 99-2 Transmissive Sensor
OF 99-3 Switch
OF 99-4 Generic Solenoid/Clutch RAP
OF 99-6 2 Wire Motor Open
OF 99-7 2 Wire Motor On
OF 99-8 Set Gate Solenoid Open
OF 99-9 Multiple Wire Motor


hcf_3_2

078-100 (HCF 3.2) Tray 6 Pre Regi Sensor On Jam
078-101 (HCF3.2) Tray 6 Feed Out Sensor On Jam
078-102 (HCF3.2) Tray 6 Regi In Sensor On Jam
078-103 (HCF3.2) J-Tra Exit Sensor On Jam
078-105 (HCF3.2) MSI Pre Feed Sensor ON Jam
078-106 (HCF3.2) Tray 6 Pre Feed Sensor On Jam
078-110 (HCF3.2) Tray 5 (MSI) Pre Regi Sensor On Jam
078-111 (HCF3.2) Regi In Sensor On Jam
078-120 (HCF3.2) MSI Feed Out Sensor On Jam
078-125 (HCF3.2) Previous Multi Feed
078-126 (HCF3.2) Multi Feed
078-127 (HCF3.2) Partial Overlap Multi Feed
078-150 (HCF3.2) Tray 7 Pre Regi Sensor On Jam
078-151 (HCF3.2) Tray 7 Feed Out Sensor On Jam
078-215 (HCF3.2) MultiFeed Check Sensor Fail
078-219 (HCF3.2) Software Download Fail
078-231 (HCF3.2) Tray 7 Shift Mechanical Fail
078-238 (HCF3.2) Tray 7 Lead Shutter Fail
078-239 (HCF3.2) Tray 7 End Shutter Fail
078-240 (HCF3.2) Tray 7 Lead Heater Fail
078-241 (HCF3.2) Tray 7 Lead Heater Temp Sensor Fail
078-250 (HCF3.2) Tray 6 Lift Up Fail
078-260 (HCF3.2) Tray 7 Lift Up Fail
078-261 (HCF3.2) Tray 6 Shift Mechanical Fail
078-262 (HCF3.2) Tray 6 Humidity Sensor Fail
078-263 (HCF3.2) Tray 6 Temp Sensor Fail
078-268 (HCF3.2) Tray 6 Lead Shutter Fail
078-269 (HCF3.2) Tray 6 End Shutter Fail
078-270 (HCF3.2) Tray 6 Lead Heater Fail
078-271 (HCF3.2) Tray 6 Lead Heater Temp Sensor Fail
078-272 (HCF3.2) HCF Cont F1 Fuse Fail
078-273 (HCF3.2) HCF Cont F2 Fuse Fail
078-274 (HCF3.2) HCF Cont F3 Fuse Fail
078-275 (HCF3.2) HCF Cont F6 Fuse Fail
078-276 (HCF3.2) HCF Cont F7 Fuse Fail
078-277 (HCF3.2) HCF Cont F8 Fuse Fail
078-278 (HCF3.2) HCF Cont F9 Fuse Fail
078-279 (HCF3.2) HCF Cont F10 Fuse Fail
078-280 (HCF3.2) HCF Cont F13 Fuse Fail
078-281 (HCF3.2) HCF Cont Fuse Fail
078-282 (HCF3.2) MSI Lift Up Fail
078-283 (HCF3.2) MSI Lift Down Fail
078-285 (HCF3.2) HCF Cont F4 Fuse Fail
078-286 (HCF3.2) HCF Cont F5 Fuse Fail
078-287 (HCF3.2) HCF Cont F11 Fuse Fail
078-288 (HCF3.2) HCF Cont F12 Fuse Fail
078-289 (HCF3.2) HCF Cont F14 Fuse Fail
078-290 (HCF3.2) HCF Cont F15 Fuse Fail
078-291 (HCF3.2) HCF Cont F16 Fuse Fail
078-298 (HCF3.2) HCF Cont F18 Fuse Fail
078-302 (HCF3.2) MSI Cover Interlock Open
078-303 (HCF3.2) J-Tra Front Cover Interlock Open
078-601 (HCF3.2) Tray 6 Lead Blower Fail
078-602 (HCF3.2) Tray 7 Lead Blower Fail
078-603 (HCF3.2) Tray 6 End Blower Fail
078-604 (HCF3.2) Tray 7 End Blower Fail
078-605 (HCF3.2) Tray 6 Front Blower Fail
078-606 (HCF3.2) Tray 7 Front Blower Fail
078-607 (HCF3.2) Tray 6 Rear Blower Fail
078-608 (HCF3.2) Tray 7 Rear Blower Fail
078-900 (HCF3.2) Tray 6 Feed Out Sensor Static Jam
078-902 (HCF3.2) MSI Feed Out Sensor Static Jam
078-904 (HCF3.2) J-Tra Exit Sensor Static Jam
078-940 (HCF3.2) Tray 6 Paper Miss Set
078-941 (HCF3.2) Tray 6 Paper Size Mismatch
078-942 (HCF3.2) Tray 7 Paper Misset
078-943 (HCF3.2) Tray 7 Paper Size Mismatch
OF-15 Chain-Link No. RAP
OF 2.5 HCF3.2 DC POWER RAP
OF1 Intermittent Fault RAP
OF2 Other Faults RAP
OF3 Audible Noise RAP
OF 99-1 Reflective Sensor RAP
OF 99-2 Transmissive Sensor
OF 99-3 Switch
OF 99-4 Generic Solenoid/Clutch RAP
OF 99-6 2 Wire Motor Open
OF 99-7 2 Wire Motor On
OF 99-8 Set Gate Solenoid Open
OF 99-9 Multiple Wire Motor

[dastin]

Расшифровка некоторых сокращений


A/D
Analog to Digital refers to conversion of signal

AC
Alternating Current is type of current available at power source for machine.

ACT
Advanced Customer Training: teaches customers to perform some of service that is normally performed by Xerox Service Representative.

ADJ
Adjustment Procedure

Bit
Binary digit, either 1 or 0, representing an electrical state.

CCD
Charge Coupled Device (Photoelectric Converter)

CD
1:Circuit Diagram; 2: Compact Disc

Chip
Integrated Circuit (IC)

CRU
Customer Replaceable Unit

DADF
Duplexing Automatic Document Feeder

DC
Direct Current is type of power for machine components. Machine converts AC power from power source to DC power.

DMM
Digital Multimeter is generic name for meter that measures voltage, current, or electrical resistance.

EME
Electromagnetic Emissions are emitted from machine during normal operation and power of these emissions are reduced by machine design features.

ESD
Electrostatic Discharge. A transfer of charge between bodies at different electrostatic potential.

FS
Fast Scan (direction) - Inboard-to Outboard

GND
Ground

HFSI
High Frequency Service Item

HVPS
High Voltage Power Supply

IIT
Image Input Terminal - the Scanner/CCD portion of the machine

IOT
Image Output Terminal - the ROS/Xero/paper handling/ fusing portion of the machine

IQ
Image Quality

KC
1000 copies

LCD
Liquid Crystal Display

LE
Lead Edge of copy or print paper, with reference to definition of term TE

LED
Light Emitting Diode

LEF
Long Edge Feed

LUT
Look Up Table - array of NVM locations that store process control data

LVPS
Low Voltage Power Supply

MF
Multi-Function

MN
Multinational

NIC
Network Interface Card

NVM
Non Volatile Memory

OGM
On-going Maintenance

PJ
Plug Jack (electrical connections)

PL
Parts List

P/O
Part of (Assembly Name)

PWB
Printed Wiring Board

PWS
Portable Workstation for Service

R/E
Reduction/Enlargement refers to features selection or components that enable reduction or enlargement

RAP
Repair Analysis Procedure for diagnosis of machine status codes and abnormal conditions

REP
Repair Procedure for disassembly and reassembly of component on machine

RIS
Raster Input Scanner

ROS
Raster Output Scanner - Device that transfers digitally processed image, using laser light, to photoreceptor.

SAD
Solid Area Density

SCP
Service Call Procedure

SEF
Short Edge Feed

Self-test
An automatic process that is used to check Control Logic circuitry. Any fault that is detected during self-test is displayed by fault code or by LEDs on PWB.

SS
Slow Scan (direction) - LE - to - TE

TE
Trail Edge of copy or print paper, with reference to definition of term LE

UI
User Interface

UM
Unscheduled Maintenance

W/
With - indicates machine condition where specified condition is present

W/O
Without - indicates machine condition where specified condition is not present

ACQS
Automatic Quality Suite

[Pavel Pe4atnikov]

dastin,
как всегда ЗАЧЕТ! Пригвоздил как "Важное"

[polexs]

правила ):

все равно респект

[Nikit0s]

...а сервис-мануалом никто не богат случайно?

[SHed]

В формате олимпии есть, т.е. эмулятор надо ставить.