24.08.2011, 23:33 | #1 |
Местный
Регистрация: 05.03.2009
Адрес: Татарстан
Сообщений: 448
Репутация: 47
|
С220 прошивка
To: KONICA MINOLTA AUTHORISED TECHNICAL PERSONNEL From: KONICA MINOLTA BUSINESS SOLUTIONS (UK) LTD TECHNICAL SUPPORT GROUP Date: 20 April 2011 Topic: bizhub C652 (DS5)5 2\C4\C52\C360\C280\C220 IU end of life message can be disabled Description With the new version of FW G00-C2 and above it is possible to disable the end of life message for consumables. This will enable the service technician to manage the replacement of consumables based on customer needs and expectation of quality. Considerations If you decide to remove the end of life message then please be aware that performance of consumables operating past the specified life is not guaranteed. This Includes copy\print quality, paper jamming and any other issues caused by extending the lifetimes. Konica Minolta UK except no responsibility for any problems that occur when extending consumable lifetimes past the Life Specification. Notes 1) All setting advised in this bulletin must be made at the same time. 2) Even though the end of life message has been removed, when the specified life value is reached the oil can warning icon will still appear. 3) The notifications on PSWC, Fiery Control Screen and CS Remote Care do not change and end of life message is still apparent (MIB information is not changed). How to apply end of life settings 1) Upgrade the FW to Version G00-C2 . 2) Make unit change setting. Service Mode > System 2 > Unit Change > Set Service for Imaging Unit. 3) Select No Stop for each consumable. For Imaging Unit\Drum Unit\Developing Unit. Service Mode > Enhanced Security Mode > IU Life stop setting > set to “no stop” For Transfer Belt and Fusing Unit Service Mode > System 2 > Software Switch Setting. Change Switch No: 55 Bit 2 _ ON (Transfer Belt Unit ‘no stop’) Bit 3 _ ON (Fusing Unit ‘no stop’) HEX should read ‘0C’ when both switches are set. 4) Eliminate Life Message Display. Service Mode > System 2 > Software Switch Setting. Change Switch No: 51 Bits 4,5,6,7 _ ON HEX should read ‘F0’ when all these switches are set. Life Specification Model Drum C\M\Y\BK Dev Unit C\M\Y Dev Unit BK Transfer Belt Fusing Unit C220 9338 M 120000 counts 600000 counts 33033 M 550000 counts C280 6244 M 120000 counts 600000 counts 22008 M 550000 counts C360 6244 M 120000 counts 600000 counts 22008 M 550000 counts Model IU C\M\Y Drum BK Dev Unit BK Transfer Belt Fusing Unit C452 5180 M 10302 M 1200000 counts 320638 M 600000 counts C552 5180 M 10302 M 1200000 counts 320638 M 600000 counts C652 (DS) 5180 M 10302 M 1200000 counts 320638 M 600000 counts Service Engineer Guide Lines when attending EM calls что скажете, где достать новую суперпрошивку? |
25.08.2011, 09:36 | #2 |
Местный
|
Ну да, убрать сообщение это очень важная проблема...
Не дурите головы, работайте на той, что есть, нет там никаких сложностей со счетчиками. Какая у вас текущая прошивка? |
25.08.2011, 15:02 | #3 |
Местный
Регистрация: 05.03.2009
Адрес: Татарстан
Сообщений: 448
Репутация: 47
|
К
AndreyBG, ак убрать сообщение о замене драм-юнитов, текущий пробег 85 тысяч, качество нормальное, после 90 вероятно требуется заменить или дальше будет печатать? |
25.08.2011, 16:09 | #4 |
Местный
Регистрация: 05.03.2009
Адрес: Татарстан
Сообщений: 448
Репутация: 47
|
прошивка G00-00
|
29.08.2011, 17:50 | #5 |
Местный
|
|
29.08.2011, 21:57 | #6 |
Местный
|
|
29.08.2011, 22:05 | #7 |
Местный
Регистрация: 05.03.2009
Адрес: Татарстан
Сообщений: 448
Репутация: 47
|
dia pason, спасибо, прошил аппарат, на днях попробую выключить сообщение о замене, отпишу
|
30.08.2011, 09:01 | #8 |
Новичок
Регистрация: 23.09.2010
Адрес: тюмень
Сообщений: 15
Репутация: 0
|
Последняя прошивочка G00-B8 нарекании нет))
|
30.08.2011, 09:05 | #9 |
Новичок
Регистрация: 23.09.2010
Адрес: тюмень
Сообщений: 15
Репутация: 0
|
|
Опции темы | |
|
"Форум индустрии цифровой печати" 2008-2023 Все вопросы по сотрудничеству: Электропочта: info@trade-print.ru Москва, Печатников пер. |