|
|
Регистрация | Пригласить друга | Все альбомы | Файловый архив | Справка | Сообщество | Календарь | Сообщения за день | Поиск |
|
Опции темы |
30.09.2019, 17:56 | #1 |
Новичок
Регистрация: 02.10.2018
Адрес: Воронеж
Сообщений: 15
Репутация: 0
|
konica minolta 5501 ошибки 3101 и3102
Как их сбросить? |
30.09.2019, 17:58 | #2 |
Местный
Регистрация: 25.07.2011
Адрес: .
Сообщений: 36,940
Репутация: 623
|
Re: konica minolta 5501 ошибки 3101 и3102
Дипсвич 3-1 в положение 0
|
30.09.2019, 18:02 | #3 |
Новичок
Регистрация: 02.10.2018
Адрес: Воронеж
Сообщений: 15
Репутация: 0
|
Re: konica minolta 5501 ошибки 3101 и3102
да
|
30.09.2019, 18:07 | #4 |
Местный
Регистрация: 25.07.2011
Адрес: .
Сообщений: 36,940
Репутация: 623
|
Re: konica minolta 5501 ошибки 3101 и3102
|
30.09.2019, 18:08 | #5 |
Новичок
Регистрация: 02.10.2018
Адрес: Воронеж
Сообщений: 15
Репутация: 0
|
Re: konica minolta 5501 ошибки 3101 и3102
|
30.09.2019, 18:20 | #6 |
Местный
Регистрация: 25.07.2011
Адрес: .
Сообщений: 36,940
Репутация: 623
|
Re: konica minolta 5501 ошибки 3101 и3102
|
30.09.2019, 18:24 | #7 |
Местный
Регистрация: 11.10.2011
Адрес: Москва
Сообщений: 2,189
Репутация: 38
|
Re: konica minolta 5501 ошибки 3101 и3102
были темы - и платы у людей вылетали, и шестеренки помогали и какя то связь с АДУ была
|
30.09.2019, 18:41 | #8 |
Местный
Регистрация: 06.07.2011
Адрес: Засратов
Сообщений: 1,180
Репутация: 52
|
Re: konica minolta 5501 ошибки 3101 и3102
|
30.09.2019, 18:43 | #9 |
Местный
Регистрация: 25.07.2011
Адрес: .
Сообщений: 36,940
Репутация: 623
|
Re: konica minolta 5501 ошибки 3101 и3102
3101: An error detection signal of M29 is detected continuously for a specified period of time while the fusing motor (M29) is ON. Solution 1. Check the connection between the rear side connector of the fusing unit and the main body side connector, and repair it if any abnormality. 2. Check the fusing unit, and repair it if any abnormality. 3. Check the connector connection and the wiring between CDB and the motor, and repair it if any abnormality. 4. Check the connector connection and the wiring between PRCB and CDB, and repair it if any abnormality. 5. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram:Main body (1/3): 3-I) 6. Replace M29. 7. Replace CDB. 8. Replace PRCB. 3102: While the fusing release home sensor (PS16) is ON, PS16 does not turn OFF within a specified period of time after the fusing motor (M29) turns ON. While PS16 is OFF, PS16 does not turn ON within a specified period of time after M29 turns ON Solution 1. Check that the front door is closed properly, and repair it if any abnormality. 2. Check the fusing unit, and repair it if any abnormality. 3. Check the connector connection and the wiring between CDB and motor/sensor, and repair it if any abnormality. 4. Check the connector connection and the wiring between PRCB and CDB, and repair it if any abnormality. 5. Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. (Wiring diagram:Main body (1/3): 3-I) 6. Check I/O and the operation of the sensor, and repair/replace it if any abnormality. (Wiring diagram: Main body (1/3): 2-I) 7. Replace M29. 8. Replace PS16. 9. Replace CDB. 10. Replace PRCB. 11. Replace M29 and CDB at a time через I\O проверьте М29, если вращается - сенсор PS16 и состояние шестеренок в редукторе. |
|
"Форум индустрии цифровой печати" 2008-2023 Все вопросы по сотрудничеству: Электропочта: info@trade-print.ru Москва, Печатников пер. |