Xerox dc 242 несовмещение лицо-оборот

[inkvis]

Всем здравствуйте.
Проблема в следующем:
Печать визиток на формата SRA4 длинной стороной.
Печатаю первую сторону - от передней кромки до изображения 6 мм.
Переворачиваю, печатаю вторую сторону, первая кромка та же.
Расстояние от кромки до изображения 8 мм.

Фото:




Собственно, как исправить?
Бумага 300 г, меловка. Бумагу под пружину ролика регистрации подложил

[Evory]

Сообщение от VLADIMIR S

Изображение смещено по отношении к центру на 1 см, соответственно оборот получается смещен на 2 см, регулирую в CWS, но в процессе печати настройки слетают и тираж в мусор, так уже не первый раз. Самый лучший вариант это регулировать сдвиг в программе верстки и пихать бумагу одной стороной. Но это опасно тем что можно на косячить, хотелось бы автоматизировать процесс. И вообще странно, такая дорогая и сложная техника, а регулировать приходится как в прошлом веке))

Если, в процессе печати, слетают настройки. То надо сервисников звать.

[Guron8499]

Здравствуйте. Недавно стал "счастливым обладателем DC 242 Fiery EX 260. Подскажите чайнику желательно поподробнее, как настроить сдвиг изображения (переднего и заднего) с 5 лотка. Писали что можно от центровать изображение ( 5мм с боков, и сверху, снизу) только вот не понял как это сделать. Заранее спасибо.

[Evory]

Job Properties-Finishing-Image Shift

[brutdakar]

Purpose
The purpose is to adjust the position of the printed image on the page. This is done by changing the value of the Lead Edge Registration and Side Edge Registration in dC129. This controls where the ROS writes the image.

Specification
The specifications for Lead Edge and Side Edge are shown in the table below.

Table 1. Specification Item
Simplex
Duplex
Tray 5 / Bypass

Lead Edge
10±1.5mm
10±1.5mm
10±1.5mm

Side Edge
8.5±1.7mm
8.5±1.7mm
8.5±2.9mm


Introduction
This series consists of the following procedures:

Lead Edge Registration, Bond/Plain Paper, Trays 1-4 and 6, Sides 1 and 2. One Lead Edge setting applies to all.

Lead Edge Registration, Bond/Plain Paper, Tray 5 / Bypass, Sides 1 and 2.

Side Edge Registration, All Trays (1 - 6), Sides 1 and 2, each set separately.

Lead Edge Registration, Heavyweight Paper, Trays 1-4 and 6, Sides 1 and 2. One Lead Edge setting applies to all.

Lead Edge Registration, Heavyweight Paper, Tray 5 / Bypass, Sides 1 and 2.

NOTE:

Whenever you adjust registration, you must perform the entire series, in the sequence given. Read the entire procedure before performing the adjustment.

Lead Edge Registration (Bond/Plain Paper)
Purpose
To correctly register the lead edge of the image in relation to the lead edge of the paper. There is a baseline lead edge setting for Trays 1 - 4 and 6 on sides 1 and 2, with a separate lead edge setting for Tray 5 / Bypass.

Check
Checking Baseline Lead Edge Registration (Trays 1 - 4 and 6)

NOTE:

You must set baseline registration for Bond/Plain paper before setting heavyweight registration.

Load Trays 1 and 2, and the Tray 5 / Bypass, with 11 x 17 / A3 Bond/Plain paper. Load Trays 3, 4, and 6 with 8 1/2 x 11 / A4 Bond/Plain paper.

The routine automatically selects the appropriate NVM location to set, based on the Paper Type setting for the trays. Ensure that all paper trays are set to the installed paper type by pressing the Setup Menu button on the UI, selecting Paper Tray Attributes, and setting and Saving the appropriate paper types for each tray. Note that if this path has changed, you will need to consult the copier/printer User Guide (Training and Information CD) for the correct menu path.

Connect the PWS to the machine and enter Diagnostic Mode.

DocuColor 240/250, select dC129 from the DC Quick menu.

DocuColor 242/252/260, select Registration, then System Registration Adjustment.

Make the following selections:

Select Side 1, if not already selected.

Select Tray 1, if not already selected.

Select 5 for Print Count.

Click Start on the PWS screen.

Label each printed sheet with the number of the print (1 through 5), the words “Tray 1,” and “Side 1,” and the location of the Lead Edge of each sheet.

Take the third print and measure from the lead edge to point A (as shown on Figure 1). Point A is at the intersection of the 7th line from the side edge and the first line from the lead edge.

If the measured value is not 10±1.5mm, perform the Adjustment. If the Check is OK, proceed to Checking Side 2 Lead Edge Registration.

Figure 1. Test Pattern Measurement Points

Checking Side 2 Lead Edge Registration

NOTE:

The grid pattern for side 1 does not align with the side 2 grid pattern; do not attempt to set registration by aligning the grids.

Make the following selections:

Select the Side 2 radio button.

Select 5 for Print Count, if not already selected.

Click Start on the PWS screen.

Label each printed sheet with the number of the print (1 through 5), the words “Tray 1” and “Side 2,” and the location of the Lead Edge of each sheet.

Take the third print and measure from the lead edge to point A (as shown on Figure 1). Point A is at the intersection of the 7th line from the side edge and the first line from the lead edge.

If the measured value is not 10±1.5mm, perform the Adjustment. If the Check is OK, proceed to Checking Tray 5 Lead Edge Registration.

Checking Tray 5 / Bypass Lead Edge Registration

Select Tray 5 (MSI) from the Tray/Size drop down box.

NOTE:

You will have to select a specific paper size for Tray 5 (MSI). Select 11 x 17 or A3 SEF (depending upon which is loaded in the Tray 5 / Bypass). Other selections are 8.5 x 11 LEF and A4 LEF.

Make the following selections:

Select the Side 1 radio button.

Select Plain as the Paper Type.

Select 5 for Print Count, if not already selected.

Click Start on the PWS screen.

Take the third print and measure from the lead edge to point A (as shown on Figure 1). Point A is at the intersection of the 7th line from the side edge and the first line from the lead edge.

If the measured value is not 10±1.5mm, perform the Adjustment. When the measured value falls within the specification, select the Side 2 radio button and repeat steps 1 through 4 to check registration for Side 2.

If the Check for Tray 5 / Bypass Side 2 is not 10±1.5mm, perform the Adjustment. If the Check is OK, proceed to Side Edge Registration.

Adjust
Use the Right and Left Arrow buttons to increase or decrease the amount of lead edge spacing. The right arrow increases the lead edge spacing (moves the grid pattern to the left). The left arrow decreases the lead edge spacing (moves the grid pattern to the right). The cumulative amount of shift is indicated in millimeters in the Lead Registration box, and is represented visually on the PWS.

After adjusting the registration, click Save Adjust Value.

After adjustment, repeat the Check procedure to see if the measured value of the Lead Edge (A) now falls within the specification of Table 1.

Repeat Adjustment steps 1 through 3 until the measured value falls within the specification.

Side Edge Registration
Purpose
To correctly register the side edge of the image in relation to the outboard edge of the paper.

Check
Check that paper is loaded in all trays, and that the paper guides are adjusted correctly.

Make the following selections:

Select the Side 1 radio button.

Select Tray 1.

Select 5 for Print Count, if not already selected.

Click Start on the PWS screen.

Label each printed sheet with the number of the print (1 through 5), the words “Tray 1,” and “Side 1,” and the location of the Lead Edge and Side Edge of each sheet.

NOTE:

With the lead edge to the right, the side edge to be checked will be at the top.

Take the third print and measure the following:

For paper larger than letter size, such as 11 x 17 / A3 (that was recommended for loading in Trays 1, 2, and Tray 5 / Bypass), measure from the intersection between the 1st line from the side edge and the 10th line from the lead edge of the paper (point B2 on Figure 1).

For letter size (8.5 x 11 / A4), paper (that was recommended for loading in Trays 3, 4, and 6), measure from the intersection between the 1st line from the side edge and the 5th line from the lead edge of the paper (point B1 on Figure 1).

If the measured value is not 8.5±1.7mm, perform the Adjustment.

If the measurement is within specification, select Trays 2 through 4, then Tray 6, and repeat steps 1 through 5 for each successive tray. Perform the Adjustment, if the measurement is not within specification.

If the measurement is within specification, select the Side 2 radio button, select Trays 2 through 4, then Tray 6, and repeat steps 1 through 5 for each successive tray for Side 2.

If the measured value for Trays 2 through 4, and Tray 6 (Side 2) is not 8.5±2.0mm, perform the Adjustment, where applicable.

If the measurement is within specification, select Tray 5 and repeat steps 1 through 5 for Side 1 of the Tray 5 / Bypass.

If the measured value for Side 1 of the Tray 5 / Bypass is not 8.5±2.9mm, perform the Adjustment.

If the measurement is within specification, select the Side 2 radio button and repeat steps 1 through 5 for Side 2 of the Tray 5 / Bypass.

If the measured value for Side 2 of the Tray 5 / Bypass is not 8.5±2.9mm, perform the Adjustment.

Adjust
Use the Up and Down Arrow buttons to increase or decrease the amount of side edge spacing. The Up arrow increases the side edge spacing (moves the image away from the outboard edge of the paper). The Down arrow decreases the side edge spacing (moves the image towards the outboard edge of the paper). The cumulative amount of shift is indicated in millimeters in the Side Registration box, and is represented visually on the PWS.

After adjusting the registration, click Save Adjust Value.

After adjustment, repeat the Check procedure to see if the measured value of the Side Edge (A) now falls within the specifications of Table 1.

Repeat Adjustment steps 1 through 3 until the measured value falls within the specification.

Lead Edge Registration, Heavyweight Paper
Check
If heavyweight paper is available, load Trays 1 and 2, and the Tray 5 / Bypass, with 11 x 17 / A3 Heavyweight paper. Load Trays 3, 4, and 6 with 8 1/2 x 11 / A4 Heavyweight paper.

NOTE:

If heavyweight paper is not available, use the same Bond/Plain paper that was used to check and adjust baseline registration for Bond/Plain paper.

NOTE:

Setting up the registration for Heavyweight 1 will automatically set up the registration for Plain Gloss media.

For Trays 1 - 4, the routine automatically selects the appropriate NVM location to set, based on the Paper Type setting for the trays (for Tray 5, you must set the paper type using the radio buttons). Ensure that all paper trays are set to a Heavyweight paper type (regardless of the actual weight of paper installed in the trays) by pressing the Setup Menu button on the UI, selecting Tray Attributes, and setting and Saving a Heavyweight paper type for each tray. Note that if this path has changed, you will need to consult the copier/printer User Guide (Training and Information CD) for the correct menu path

Repeat the previously stated procedures for Checking and Adjusting (if necessary) Lead Edge Registration (for Bond/Plain Paper) for Trays 1 - 4 and 6, as well as the procedures for Checking and Adjusting (if necessary) the Tray 5 / Bypass Lead Edge Registration.

[Guron8499]

Сообщение от Evory

Job Properties-Finishing-Image Shift

Спасибо за ответ. Скажите как и откуда зайти в это меню?

[Guron8499]

Сообщение от brutdakar

Purpose
The purpose is to adjust the position of the printed image on the page. This is done by changing the value of the Lead Edge Registration and Side Edge Registration in dC129. This controls where the ROS writes the image.

Specification
The specifications for Lead Edge and Side Edge are shown in the table below.

Table 1. Specification Item
Simplex
Duplex
Tray 5 / Bypass

Lead Edge
10±1.5mm
10±1.5mm
10±1.5mm

Side Edge
8.5±1.7mm
8.5±1.7mm
8.5±2.9mm


Introduction
This series consists of the following procedures:

Lead Edge Registration, Bond/Plain Paper, Trays 1-4 and 6, Sides 1 and 2. One Lead Edge setting applies to all.

Lead Edge Registration, Bond/Plain Paper, Tray 5 / Bypass, Sides 1 and 2.

Side Edge Registration, All Trays (1 - 6), Sides 1 and 2, each set separately.

Lead Edge Registration, Heavyweight Paper, Trays 1-4 and 6, Sides 1 and 2. One Lead Edge setting applies to all.

Lead Edge Registration, Heavyweight Paper, Tray 5 / Bypass, Sides 1 and 2.

NOTE:

Whenever you adjust registration, you must perform the entire series, in the sequence given. Read the entire procedure before performing the adjustment.

Lead Edge Registration (Bond/Plain Paper)
Purpose
To correctly register the lead edge of the image in relation to the lead edge of the paper. There is a baseline lead edge setting for Trays 1 - 4 and 6 on sides 1 and 2, with a separate lead edge setting for Tray 5 / Bypass.

Check
Checking Baseline Lead Edge Registration (Trays 1 - 4 and 6)

NOTE:

You must set baseline registration for Bond/Plain paper before setting heavyweight registration.

Load Trays 1 and 2, and the Tray 5 / Bypass, with 11 x 17 / A3 Bond/Plain paper. Load Trays 3, 4, and 6 with 8 1/2 x 11 / A4 Bond/Plain paper.

The routine automatically selects the appropriate NVM location to set, based on the Paper Type setting for the trays. Ensure that all paper trays are set to the installed paper type by pressing the Setup Menu button on the UI, selecting Paper Tray Attributes, and setting and Saving the appropriate paper types for each tray. Note that if this path has changed, you will need to consult the copier/printer User Guide (Training and Information CD) for the correct menu path.

Connect the PWS to the machine and enter Diagnostic Mode.

DocuColor 240/250, select dC129 from the DC Quick menu.

DocuColor 242/252/260, select Registration, then System Registration Adjustment.

Make the following selections:

Select Side 1, if not already selected.

Select Tray 1, if not already selected.

Select 5 for Print Count.

Click Start on the PWS screen.

Label each printed sheet with the number of the print (1 through 5), the words “Tray 1,” and “Side 1,” and the location of the Lead Edge of each sheet.

Take the third print and measure from the lead edge to point A (as shown on Figure 1). Point A is at the intersection of the 7th line from the side edge and the first line from the lead edge.

If the measured value is not 10±1.5mm, perform the Adjustment. If the Check is OK, proceed to Checking Side 2 Lead Edge Registration.

Figure 1. Test Pattern Measurement Points

Checking Side 2 Lead Edge Registration

NOTE:

The grid pattern for side 1 does not align with the side 2 grid pattern; do not attempt to set registration by aligning the grids.

Make the following selections:

Select the Side 2 radio button.

Select 5 for Print Count, if not already selected.

Click Start on the PWS screen.

Label each printed sheet with the number of the print (1 through 5), the words “Tray 1” and “Side 2,” and the location of the Lead Edge of each sheet.

Take the third print and measure from the lead edge to point A (as shown on Figure 1). Point A is at the intersection of the 7th line from the side edge and the first line from the lead edge.

If the measured value is not 10±1.5mm, perform the Adjustment. If the Check is OK, proceed to Checking Tray 5 Lead Edge Registration.

Checking Tray 5 / Bypass Lead Edge Registration

Select Tray 5 (MSI) from the Tray/Size drop down box.

NOTE:

You will have to select a specific paper size for Tray 5 (MSI). Select 11 x 17 or A3 SEF (depending upon which is loaded in the Tray 5 / Bypass). Other selections are 8.5 x 11 LEF and A4 LEF.

Make the following selections:

Select the Side 1 radio button.

Select Plain as the Paper Type.

Select 5 for Print Count, if not already selected.

Click Start on the PWS screen.

Take the third print and measure from the lead edge to point A (as shown on Figure 1). Point A is at the intersection of the 7th line from the side edge and the first line from the lead edge.

If the measured value is not 10±1.5mm, perform the Adjustment. When the measured value falls within the specification, select the Side 2 radio button and repeat steps 1 through 4 to check registration for Side 2.

If the Check for Tray 5 / Bypass Side 2 is not 10±1.5mm, perform the Adjustment. If the Check is OK, proceed to Side Edge Registration.

Adjust
Use the Right and Left Arrow buttons to increase or decrease the amount of lead edge spacing. The right arrow increases the lead edge spacing (moves the grid pattern to the left). The left arrow decreases the lead edge spacing (moves the grid pattern to the right). The cumulative amount of shift is indicated in millimeters in the Lead Registration box, and is represented visually on the PWS.

After adjusting the registration, click Save Adjust Value.

After adjustment, repeat the Check procedure to see if the measured value of the Lead Edge (A) now falls within the specification of Table 1.

Repeat Adjustment steps 1 through 3 until the measured value falls within the specification.

Side Edge Registration
Purpose
To correctly register the side edge of the image in relation to the outboard edge of the paper.

Check
Check that paper is loaded in all trays, and that the paper guides are adjusted correctly.

Make the following selections:

Select the Side 1 radio button.

Select Tray 1.

Select 5 for Print Count, if not already selected.

Click Start on the PWS screen.

Label each printed sheet with the number of the print (1 through 5), the words “Tray 1,” and “Side 1,” and the location of the Lead Edge and Side Edge of each sheet.

NOTE:

With the lead edge to the right, the side edge to be checked will be at the top.

Take the third print and measure the following:

For paper larger than letter size, such as 11 x 17 / A3 (that was recommended for loading in Trays 1, 2, and Tray 5 / Bypass), measure from the intersection between the 1st line from the side edge and the 10th line from the lead edge of the paper (point B2 on Figure 1).

For letter size (8.5 x 11 / A4), paper (that was recommended for loading in Trays 3, 4, and 6), measure from the intersection between the 1st line from the side edge and the 5th line from the lead edge of the paper (point B1 on Figure 1).

If the measured value is not 8.5±1.7mm, perform the Adjustment.

If the measurement is within specification, select Trays 2 through 4, then Tray 6, and repeat steps 1 through 5 for each successive tray. Perform the Adjustment, if the measurement is not within specification.

If the measurement is within specification, select the Side 2 radio button, select Trays 2 through 4, then Tray 6, and repeat steps 1 through 5 for each successive tray for Side 2.

If the measured value for Trays 2 through 4, and Tray 6 (Side 2) is not 8.5±2.0mm, perform the Adjustment, where applicable.

If the measurement is within specification, select Tray 5 and repeat steps 1 through 5 for Side 1 of the Tray 5 / Bypass.

If the measured value for Side 1 of the Tray 5 / Bypass is not 8.5±2.9mm, perform the Adjustment.

If the measurement is within specification, select the Side 2 radio button and repeat steps 1 through 5 for Side 2 of the Tray 5 / Bypass.

If the measured value for Side 2 of the Tray 5 / Bypass is not 8.5±2.9mm, perform the Adjustment.

Adjust
Use the Up and Down Arrow buttons to increase or decrease the amount of side edge spacing. The Up arrow increases the side edge spacing (moves the image away from the outboard edge of the paper). The Down arrow decreases the side edge spacing (moves the image towards the outboard edge of the paper). The cumulative amount of shift is indicated in millimeters in the Side Registration box, and is represented visually on the PWS.

After adjusting the registration, click Save Adjust Value.

After adjustment, repeat the Check procedure to see if the measured value of the Side Edge (A) now falls within the specifications of Table 1.

Repeat Adjustment steps 1 through 3 until the measured value falls within the specification.

Lead Edge Registration, Heavyweight Paper
Check
If heavyweight paper is available, load Trays 1 and 2, and the Tray 5 / Bypass, with 11 x 17 / A3 Heavyweight paper. Load Trays 3, 4, and 6 with 8 1/2 x 11 / A4 Heavyweight paper.

NOTE:

If heavyweight paper is not available, use the same Bond/Plain paper that was used to check and adjust baseline registration for Bond/Plain paper.

NOTE:

Setting up the registration for Heavyweight 1 will automatically set up the registration for Plain Gloss media.

For Trays 1 - 4, the routine automatically selects the appropriate NVM location to set, based on the Paper Type setting for the trays (for Tray 5, you must set the paper type using the radio buttons). Ensure that all paper trays are set to a Heavyweight paper type (regardless of the actual weight of paper installed in the trays) by pressing the Setup Menu button on the UI, selecting Tray Attributes, and setting and Saving a Heavyweight paper type for each tray. Note that if this path has changed, you will need to consult the copier/printer User Guide (Training and Information CD) for the correct menu path

Repeat the previously stated procedures for Checking and Adjusting (if necessary) Lead Edge Registration (for Bond/Plain Paper) for Trays 1 - 4 and 6, as well as the procedures for Checking and Adjusting (if necessary) the Tray 5 / Bypass Lead Edge Registration.

Спасибо за Ваш ответ.

[Guron8499]

Всё нашел, спасибо. Буду пробовать.