Xerox WC7345 error 004-350 - Цифровая печать как бизнес - форум и портал
Индустрия цифровой печати - отраслевой портал  

Вернуться   Цифровая печать как бизнес - форум и портал > Технический раздел - ремонт принтеров, копиров > XEROX

Реклама на форуме
  • Дополнительный доход для сервисного инженера. Узнать как…
Ответ
 
Опции темы
Старый 24.02.2021, 15:39   #1
akrpkn
Пользователь
 
Регистрация: 07.05.2014
Адрес: Льгов
Сообщений: 43
Репутация: 0
По умолчанию Xerox WC7345 error 004-350

Здравствуйте, аппарат Xerox WC7345 выдает ошибку 004-350. Данную ошибку выдает, только когда начинаешь копирование, в режиме ожидания ошибка не выскакивает. Подскажите, в чем дело.
akrpkn вне форума   Ответить с цитированием
Старый 24.02.2021, 22:15   #2
Barmalei
Новичок
 
Регистрация: 24.02.2021
Адрес: Kharkov
Сообщений: 12
Репутация: 0
По умолчанию Re: Xerox WC7345 error 004-350

Обрати внимание на срок службы Drum, могут быть на 0 %
Barmalei вне форума   Ответить с цитированием
Старый 02.03.2021, 21:36   #3
akrpkn
Пользователь
 
Регистрация: 07.05.2014
Адрес: Льгов
Сообщений: 43
Репутация: 0
По умолчанию Re: Xerox WC7345 error 004-350

Цитата:
Сообщение от Barmalei Посмотреть сообщение
Обрати внимание на срок службы Drum, могут быть на 0 %
1. Установил новые драмы, ремень переноса,
девелоперы, тонер-катриджи.
Проблема осталась error 004-350 IOT Video Failure.
2. Провел NVM All Reset.
3. Обновил FW v. 1.237.123 до 1.237.4.
4. Через Service Diagnostic Tools определил -
не крутят моторы приводов драмов.
5. Проверил основные напряжения - все ОК.
6. Нашел точно такую рабочую машину.
Поменял местами основную плату управления.
Проблема перешла на другую машину.
Вывод : неисправна плата PWBA MCU.
7. Прозвонил на плате все что мог. Прогрел чипы.

Обратил внимание на основной чип в корпусе BGA.
На форуме copytechnet.com указали, что с ним связаны
основные проблемы на плате. Поменять не на что.

Вопрос ; где купить плату PWBA MCU p\n 960K31353 ?
Подходят от WC7228-7235-7245-7328-7335-7345.
akrpkn вне форума   Ответить с цитированием
Старый 03.03.2021, 00:13   #4
Barmalei
Новичок
 
Регистрация: 24.02.2021
Адрес: Kharkov
Сообщений: 12
Репутация: 0
По умолчанию Re: Xerox WC7345 error 004-350

Был бюлетень по этой ошибки , советуют Using Special Boot Modes, GP 14 cleared the faults and reset the HSFI's to normal status.

GP 14 Special Boot Modes
Purpose
This procedure describes methods of recovering from certain un-clearable faults.

Procedure
Some boot-up failures, as well as some un-clearable fault codes, may be caused by software corruption, or by structural flaws in a command sent to the machine. In these cases, it is sometimes possible to bypass or delete the offending code during the startup process.


CAUTION
There are four special boot modes. Each mode performs a different set of initializations to bypass a specific set of problems. There is information lost in each procedure, thus, they should not be used unless specific directions are given. The following list gives these procedures, in the order from least-invasive to most-invasive. If you are instructed to perform a specific initialization, perform only that procedure. If you are asked to perform the entire series, perform the steps in the order given, until the problem is resolved.

Job Log Initialization
This step will delete any print or copy job that is in process, and then perform a reboot.

To execute: simultaneously press and hold the 1, the Stop, and the Power Save buttons on the Control Panel while switching on the power. Hold the buttons down until the boot up screen (progress bar) appears.

Spool Initialization
This step will delete all pending print or copy jobs in the job queue, and then perform a reboot.

To execute: simultaneously press and hold the 6, the Stop, and the Power Save buttons on the Control Panel while switching on the power. Hold the buttons down until the boot up screen (progress bar) appears.

HGP 14 Special Boot ModesDD Initialization
This step will delete all pending print or copy jobs in the IOT job queue, initializes the IOT HDD, and will and then perform a reboot. All customer data on the HDD will be deleted.

To execute: simultaneously press and hold the 4, the Stop, and the Power Save buttons on the Control Panel while switching on the power. Hold the buttons down until the boot up screen (progress bar) appears.

ESS NVM Initialization

CAUTION
STOP HERE! This portion of the routine will set all IOT ESS NVM values to default. DO NOT execute this portion unless specifically directed to perform this portion.

Do not attempt this part of the procedure unless there is a known-good Machine Settings floppy, an accurate Configuration Report and/or other data that will enable you to reload the correct NVM values for this machine.

This step will initialize the IOT ESS NVM (SYS-System and SYS-User) and then perform a reboot.

To execute: simultaneously press and hold the 3, the Stop, and the Power Save buttons on the Control Panel while switching on the power. Hold the buttons down until the boot up screen (progress bar) appears.
Barmalei вне форума   Ответить с цитированием
Ответ

Опции темы

Быстрый переход

183 204 195 210 237 243 263 7 8 152 15 16 13 11 10 14 35 9 256 123 37 144 145 146 179 20 258 21 22 124 23 24 97 127 128 25 26 126 136 154 64 65 254 233 159 162 163 164 66 27 98 48 56 120 58 59 60 61 62 135 63 165 166 200 201 202 51 53 167 169 168 172 52 55 54 125 255 207 217 218 219 220 221 222 223 224


"Форум индустрии цифровой печати" 2008-2023

Все вопросы по сотрудничеству:

Электропочта: info@trade-print.ru

Москва, Печатников пер.

Текущее время: 15:41. Часовой пояс GMT +4.

Яндекс.Метрика