07.04.2021, 13:05 | #1 |
Местный
Регистрация: 26.12.2011
Адрес: Пермь
Сообщений: 537
Репутация: 17
|
C1060L error C‐D0F1
|
07.04.2021, 21:13 | #2 |
Местный
Регистрация: 10.02.2011
Адрес: Алма-Ата
Сообщений: 2,991
Репутация: 262
|
Re: C1060L error C‐D0F1
Code
C-D0F1 Classification Main body: Overall control EEPROM abnormality Cause EEPROM cannot be accessed normally Measures to take when an alert occurs The main body and the option stop immediately to deactivate the main relay. Estimated abnormal parts • Overall control board (OACB) • EEPROM Correction Note • The message "Please call service" is displayed on the panel. Solution 1. Check the installation status of EEPROM, and repair it when there is any abnormality. 2. When the HDD lock password is disabled, replace OACB (Refer to "G.3.2.8 Overall control board (OACB)") 3. When the HDD lock password is enabled, contact the service manager of KMBT. |
08.04.2021, 07:27 | #3 | |
Местный
Регистрация: 26.12.2011
Адрес: Пермь
Сообщений: 537
Репутация: 17
|
Re: C1060L error C‐D0F1
Цитата:
2. Когда пароль блокировки жесткого диска отключен, замените OACB (см. "G. 3.2.8 Общая плата управления (OACB)") Ссылочкой на сервис-мануал не поделитесь ? |
|
08.04.2021, 18:59 | #4 |
Местный
Регистрация: 10.02.2011
Адрес: Алма-Ата
Сообщений: 2,991
Репутация: 262
|
Re: C1060L error C‐D0F1
|
12.04.2021, 10:00 | #5 |
Местный
Регистрация: 26.12.2011
Адрес: Пермь
Сообщений: 537
Репутация: 17
|
Re: C1060L error C‐D0F1
|
16.12.2022, 10:46 | #6 |
Новичок
Регистрация: 16.12.2022
Адрес: Москва
Сообщений: 1
Репутация: 0
|
Re: C1060L error C‐D0F1
Здравствуйте. Тоже проблема, потер у себя сервис-мануал, а тут вылезла ошибка C-3801, если можно ссылочку на него, буду признателен.
|
19.12.2022, 20:04 | #7 |
Местный
Регистрация: 10.04.2009
Адрес: РФ
Сообщений: 1,319
Репутация: 32
|
Re: C1060L error C‐D0F1
Code
C-3801* Classification Main body: Fusing low temperature abnormality Cause Fusing low temperature abnormality. During the fusing idling or printing, the fusing temperature sensor/1 (TH1) detects that the temperature is less than 100°C continuously for a specified period of time. Measures to take when an alert occurs The main body and the option stop immediately to deactivate the main relay. Estimated abnormal parts • Fusing unit • Printer control board (PRCB) • DC power supply/1 (DCPS1) • Fusing control board/1 (FUSCB1) (Only for Europe) • Fusing heater lamp/1 (L1) • Fusing temperature sensor/1 (TH1) • Thermostat/1 (TS1) Correction WARNING • Be sure to select the DIPSW3-1 to 0 after you replace the defective parts. If DIPSW3-1 is selected to 0 before defective parts are fixed, it possibly cause a fire. Note • The message "Please call service" is displayed on the panel. Solution 1. Check the connection between the rear side connector of the fusing unit and the main body side connector, and repair it when there is any abnormality. 2. Check the connector connection and the wiring between the fusing temperature sensor and the PRCB, and repair it when there is any abnormality. 3. Check the connector connection and the wiring between the fusing heater lamp and the DCPS1, and repair it when there is any abnormality. (Wiring diagram: Main body (1/4): 3-C, 3-D) 4. Check the connector connection and the wiring among the fusing heater lamp, the FUSC |
Опции темы | |
|
"Форум индустрии цифровой печати" 2008-2023 Все вопросы по сотрудничеству: Электропочта: info@trade-print.ru Москва, Печатников пер. |